資訊 / 電信 ITE / Telecom

Argentina阿根廷

阿根廷發佈新的合格評定規則

阿根廷工貿部於2025年2月25日發佈第 16/2025 號決議，為在阿根廷銷售的電氣設備制定了新的基本品質和安全要求。

產品範圍

該法規涵蓋的產品列於附件二，分為四大類：

• 電源和電池充電器
• 家用電器
• 照明設備
• ITE、A&V、辦公設備

範圍內的所有產品必須符合附件一中詳細列出的基本品質和安全要求。

The Secretaría de Industria y Comercio in Argentina has recently published Resolución 16/2025, which establish new essential quality and safety requirements for electrical equipment marketed in Argentina.

This Resolution, along with its annexes, form an integral part of the regulatory framework introduced by Resolution No. 237/2024, which set forth a new general conformity framework for products requiring certification under a Technical Regulation.

Scope of Products

The products covered under this regulation are listed in Annex II and fall into four categories:

• Power supplies and chargers
• Household electrical appliances
• Lighting devices
• Electronic, audio, and video equipment

All products within the scope must meet the essential quality and safety requirements detailed in Annex I.

 

澳洲 Australia

澳洲對無線通訊 (低干擾設備) 類別證書的諮詢意見

[法規草案] 2015 年無線通訊 (低干擾設備) 類別許可證將於 2025 年 10 月 1 日到期。

為了促進新技術的使用，ACMA 發佈了重新制定 LIPD 類別證書的諮詢意見，將於 2025 年 5 月 16 日結束。

The Radiocommunications (Low Interference Potential Devices) Class Licence 2015 is due to sunset on 1 October 2025.

To introduce minor changes and facilitate the use of emerging technoligies, ACMA published the consultation to remake the LIPD class licence​.

The consultation will close on May 16, 2025.

 

澳洲 Australia

澳洲/紐西蘭標準即將修訂AS/NZS 4417.2並納入新增產品種類

澳洲標準局/紐西蘭標準局即將發佈對 AS/NZS 4417.2 的修訂。該修訂把以下產品納入 EESS 2/3 級設備：

– 電動車供電設備 (EVSE): 3級

– 電池儲能系統 (BESS) 設備: 3級

– 電源線延長配件: 2級

– 熱泵熱水器: 2級

– 可擕式儲能電源: 3級
產品除 IEC 標準外，還須符合 AS/NZS 60335.1 第 30.2 條。耐火需求將作為澳洲/紐西蘭偏差添加到 AS/NZS 標準。

本修正案公佈後，以下要求將有12個月的過渡期:

– EESS 2 級設備：必須有測試報告證明符合要求，必須在 EESS 資料庫上註冊並需繳納註冊費

– EESS 3 級設備：必須具有COA核准證書，必須在 EESS 資料庫中註冊並需繳交註冊費

Standards Australia Limited/Standards New Zealand will publish an amendment to AS/NZS 4417.2 soon. The amendment will include the following products as EESS Level 2/3 equipment:

• Electric Vehicle Supply Equipment (EVSE): Level 3
• Battery Energy Storage System (BESS) Equipment: Level 3
• Cord Extension Set: Level 2
• Heat Pump Water Heater: Level 2
• Portable Power Station: Level 3

In addition to the IEC standards (Standard Australia is in the process of adopting IEC standards as AS/NZS standards for EVSE products), the product must also comply with Clause 30.2 of AS/NZS 60335.1. The Resistance to Fire requirements will be added in the AS/NZS standards as Australian/New Zealand deviations.

Once this Amendment is published, there are 12 months transition period for the following requirements to take effect.

• EESS Level 2 Equipment: Must have a test report to show compliance, must be registered on EESS database and registration fees apply;
• EESS Level 3 Equipment: Must have a Certificate of Approval, must be registered on EESS database and registration fees apply.

 

Australia澳洲

ACMA重新制定《2015 年電信 (使用者設備和使用者佈線標籤通知) 法規》及更新8項標準

2024年10月31日，澳洲通信和媒體管理局 (ACMA) 就重新制定《2015 年電信 (使用者設備和使用者佈線標籤通知) 法規》、7 項電信標準以及《電信殘疾人標準》進行了公眾諮詢。

ACMA 於 2025 年 3 月 20 日發佈了此次公眾諮詢的結果。《殘疾人標準》和7項技術標準已於 2025 年 3 月 30 日生效，《電信標籤通知》已於 2025 年 3 月 31 日生效。七項技術標準分別為：

• AS/CA S002電信 (連接交換電話網絡的使用者設備類比互通和抗干擾要求) 技術標準 2025
• AS/CA S003電信 (連接電信網路的使用者接入設備要求) 技術標準 2025
• AS/CA S004電信 (使用者設備語音性能要求) 技術標準 2025
• AS/CA S008電信 (使用者佈線產品要求) 技術標準 2025
• AS/ACIF S016電信 (具有分層數位介面的使用者設備要求) 技術標準 2025
• AS/CA S041電信 (連接交換電話網絡的 DSL 使用者設備要求) 技術標準 2025
• AS/CA S043電信 (連接電信網路金屬本地環路介面的使用者設備要求) 技術標準 2025

On 31 October 2024, the Australian Communications and Media Authority (ACMA) launched a public consultation on the reformulation of the Telecommunications (Labelling Notice for Customer Equipment and Customer Cabling) Regulations 2015, and seven telecommunications standards, and the Telecommunications Disability Standard. The ACMA published the results of this public consultation on 20 March 2025. The Disability Standards and 7 technical standards have entered into force on March 30, 2025, and the Telecommunication Labeling Notice has entered into force on March 31, 2025. The seven technical standards are:

• Telecommunications (Analogue Interworking and Non-interference Requirements for Customer Equipment for Connection to a Switched Telephone Network – AS/CA S002) Technical Standard 2025
• Telecommunications (Requirements for Customer Access Equipment for Connection to a Telecommunications Network – AS/CA S003) Technical Standard 2025
• Telecommunications (Voice Performance Requirements for Customer Equipment – AS/CA S004) Technical Standard 2025
• Telecommunications (Requirements for Customer Cabling Products – AS/CA S008) Technical Standard 2025
• Telecommunications (Requirements for Customer Equipment with Hierarchical Digital Interfaces – AS/ACIF S016) Technical Standard 2025
• Telecommunications (Requirements for DSL Customer Equipment for Connection to a Switched Telephone Network – AS/CA S041) Technical Standard 2025
• Telecommunications (Requirements for Customer Equipment for Connection to a Metallic Local Loop Interface of a Telecommunications Network – AS/CA S043) Technical Standard 2025

Click on the link to view the original ACMA public consultation.

 

Chile智利

智利發佈移動設備使用 USB-C 埠作為充電標準的草案

[法規草案] 2025年4月16日，智利公佈了關於移動資訊和電信設備及充電器的WTO諮詢文件。該法規建立了移動設備及其充電器之間的互通性，要求某些設備 (例如手機、平板電腦和筆記型電腦) 使用 USB-C 埠作為充電標準。同時，該法規定義了基於國際標準的技術規範，並要求供應商明確說明是否附帶充電器以及設備的充電規格。

目前該草案正在搜集意見中，擬議的採納日期和生效日期尚未確定。

On 16 April 2025, Chile published a WTO consultation document about mobile information and telecommunications devices and chargers. The regulation establishes common interoperability between mobile devices and their chargers, mandating that certain devices, such as phones, tablets, and laptops, use the USB-C port as a charging standard. It also defines technical standards based on international standards and requires suppliers to clearly state whether they include a charger and the device’s charging specifications.

The deadline for submission of comments is 60 days from notification. The proposed adoption date and proposed effective date are not determined yet.

 

China中國

中國發佈關於投影機能效限定值及能源效率等級的規範

[法規草案] 2025年3月13日，中國發佈關於投影機能效限定值及能源效率等級的WTO通報。本標準規定了投影機的能效等級、能效限定值及測試方法，適用於以投影為主要功能，以高壓汞燈、雷射、LED燈為光源的液晶顯示 (LCD) 和數位光處理 (DLP) 投影機。採用矽基液晶 (LCOS) 作為顯示器件的投影機可參考本文件執行。

本檔不適用於由投影螢幕和投影機組成的一體化投影單元。

On 13 March 2025, China published a WTO Notification about minimum allowable values of energy efficiency and energy efficiency grades for projectors.

This document specifies the energy efficiency grades, minimum allowable values of energy efficiency, and testing methods for projectors.

This document applies to liquid crystal display (LCD) and digital light processing (DLP) projectors with projection as the main function and high-pressure mercury lamps, lasers, and LED lamps as light sources. Projectors using liquid crystal on silicon (LCOS) as display devices can refer this document for implementation.

This document does not apply to integrated projection units consisting of projection screens and projectors.

 

India印度

有關OEM提交原始碼以及在ComSec計畫下發放臨時證書 (Pro Tem Certificate)

印度國家通訊安全中心 (NCCS) 發佈備忘錄，包含有關根據 ComSec 計畫頒發 ProTem 證書的原始程式碼提交的最新資訊。涉及的設備: IP 路由器、WiFi CPEs、路由器、IP、5G SMF、OLT、ONT

可接受提交原始碼或由工具生成的無改寫/重組的內部測試報告，截止日期為2025年12月31日，符合ITSAR要求且附帶測試結果或聲明書者，可獲得6個月有效的臨時證書，可依情況延長。自2026年1月1日起，送測設備必須提交原始碼。

Regarding Submission of Source code by OEMs and issue of Pro Tem Certificate under ComSec scheme, NCCS has issued a memorandum and approved the the submission of Source Code and the issue of Pro Tem Certificate under the ComSec scheme.

Device/Equipment involved: IP Routers, WiFi CPEs, Routers, IP, 5G SMF, OLT, ONT

Source code submission or internal test report generated from the tool with no paraphrasing/transposition will be accepted till 31.12.2025; compliance to ITSAR supported by test result or undertaking for Pro-Tem certificate valid for 6 months. Source code submission is mandatory for devices submitted for testing w.e.f. 01.01.2026

 

India印度

印度NCCS發佈通知延長ONT和OLT自願安全認證和強制性安全認證的日期

國家通訊安全中心 (NCCS) 發佈有關 ComSec 計畫下光網路終端 (ONT) 和光線路終端 (OLT) 產品安全認證的通知，此新通知取代 2024 年 12 月 6 日發佈的通知。

主要內容：

• 自願安全認證 (VSC) 制度已延長至 2025 年 8 月 31 日。
• 在此期間不會徵收任何行政費用或安全測試評估費。
• 強制性安全認證的日期也已延長。自 2025 年 9 月 1 日起，這些產品將接受 ComSec 計畫下 ITSAR 合規強制性認證。

The National Centre for Communication Security (NCCS) has issued a notification concerning the Security Certification of Optical Network Terminal (ONT) and Optical Line Terminal (OLT) products under the ComSec scheme. This new notification replaces the one issued on December 6th, 2024.

Key Points of this notification:

• Voluntary Security Certification (VSC) regime has been extended till 31st August 2025.
• No administrative or Security Test Evaluation Fee will be levied during this period.
• Date for Mandatory Security Certification has also been extended. Starting 1st September 2025, mandatory certification for compliance to ITSAR under the ComSec scheme will apply to these products.

OEMs, importers, dealers, and users of telecom equipment can apply for the Voluntary Security Certificate via the online portal. This is a crucial update for ensuring compliance and security within the telecom industry.

 

India印度

印度BIS公告類比式監控攝影機(Analog CCTV Camera 不需符合《CCTV安全基本要求》(ER 01:2024)及其相關更新作法

印度BIS公告類比監控攝影機(Analog CCTV Camera 不需符合《CCTV安全基本要求》(ER 01:2024)，類比型之外的CCTV camera皆須符合IS 13252 -1+ER:01。

• 針對現有類比式監控攝影機，製造商需在2025年4月9日前透過線上模組提交自我聲明。逾期未聲明或不符合規定的型號將從許可範圍中移除。
• 未來所有CCTV camera的測試報告，都必須清楚註明是否為類比式型號。

此外, 自2025年4月9日起，所有CCTV camera設備必須符合《CCTV安全基本要求》(ER 01:2024)，以強化公共與私人監控系統的資安防護。已持有相關BIS認證 (IS 13252 (Part 1)的製造商，也必須在2025年4月9日前完成所有符合性測試，並線上提交檢測報告。2025年4月9日之後，不合規的型號將自許可範圍中刪除。若未能在 2025 年 4 月 9 日之前採取必要措施，或所有模型均不符合要求，則證書將被取消。

Indian BIS announced Security ER:01 is non-applicability to Analog CCTV Cameras. Other than Analog type of CCTV camera, it need to comply IS 13252-1+ER:01

• For existing Analog CCTV cameras, manufacturers must submit a self-declaration through the online module by April 9, 2025. Models not declared or not compliant with requirements after this date will be removed from the scope of the license.
• All future test reports for CCTV cameras must clearly indicate whether the model is Analog.

Furthermore, after April 9, 2025, all CCTV camera equipment must comply with the “Essential Requirement(s) for Security of CCTV Order” to strengthen the security protection of public and private surveillance systems.

From April 9, 2025, all new manufacturers applying for India BIS safety certification must fully comply with the above regulations. Manufacturers that currently hold relevant BIS certification (IS 13252 (Part 1): 2010 / IEC 60950-1:2005) must also complete all compliance tests before April 9, 2025 and submit test reports online. After 09 April 2025, non-compliant models shall be deleted from the scope of License. If the Licensee fails to take necessary action by 09 April 2025 or if none of the models are complying, License shall be liable for cancellation.

 

India印度

MEITY通知“需符合附加印度標準 IS 18112: 2022的電視機( Television Sets)“的實施日期延長至2025年10月26日

MEITY通知“需符合附加印度標準 IS 18112: 2022的電視機( Television Sets)“原訂於 2025 年 4 月 26 日生效。但經與利害關係人討論後，MEITY特此通知該命令的實施日期延長至2025年10月26日。

MEITY had notified “Television Sets to comply with additional Indian Standard IS 18112: 2022” under CRO VI which was given the date 26th April, 2025 to come into effect.
After discussing with stakeholders, MEITY hereby notified that the date of implementation of the Order stands extended to 26th October, 2025.

 

Iraq伊拉克

伊拉克CMC就短距離無線設備和超寬頻法規草案啟動公眾諮詢

[法規草案] 2025 年 4 月 13 日，伊拉克通訊與媒體委員會 (CMC) 就短距離無線設備 (SRD) 和超寬頻 (UWB) 法規草案啟動公眾諮詢。 SRD設備法規包含多個系列的無線設備，參考對應的歐盟技術標準，無版本限制。對於Wi-Fi 6e來說，標準是EN 303 687，頻段為5925-6425MHz，功率限制為200mW，僅限室內使用。評論期至2025年5月13日。

On 13 April 2025, Iraq’s Communications and Media Commission (CMC) launched a public consultation on draft regulations for short-range wireless devices (SRDs) and ultra-wideband (UWB). The SRD equipment regulation contains several series of wireless devices, which refers to the corresponding EU technical standards without version. For Wi-Fi 6e, the standard is EN 303 687 , the frequency band is 5925-6425MHz, the power limit is 200mW, and it is only for indoor use.

The comment period is until 13 May 2025.

 

Israel以色列

標準管理局發布關於進口產品受“SI 32 Part 1.1”和“SI 32 Part 2.5”標準規範的通知

標準管理局向進口公眾發布通知，將標準“SI 32 Part 1.1”和“SI 32 Part 2.5”從符合歐洲法規的軌道上移除。這些標準涵蓋的產品的電氣安全，因歐洲層級並沒有統一的規定，產品均受各國國家立法的約束。

此外，LVD指令 (附件II) 明確規定插頭和插座不受此指令的約束。

有鑑於此，決定取消這些產品的歐洲監管合規軌道。

The Standards Administration publishes a notice to the importing public regarding the removal of the standards   “SI 32 Part 1.1” and “SI 32 Part 2.5” from the track for compliance with European regulations.

With the beginning of the “What’s good for Europe is good for Israel” reform, standards were defined: “SI 32 Part 1.1” and “SI 32 Part 2.5” as suitable for the alignment track with the European regulation.

However, after further in-depth examination, it emerged that regarding the electrical safety of the products covered by these standards, there is no uniform regulation at the European level and the products are subject to the national legislation of each country.

Furthermore, the LVD Directive (Annex II) explicitly states that plugs and sockets are not covered by the Directive.

In light of this, it was decided to cancel the European regulatory compliance track for these products.

 

Japan日本

日本總務省正在就5G毫米波行動通訊系統的技術要求徵求公眾意見

[法規草案] 2025年4月3日，日本總務省就下一代行動通訊系統委員會關於5G行動通訊系統 (26GHz頻段/40GHz頻段) 技術要求的報告草案公開徵求意見。

點擊連結查看公眾諮詢原文，評論期至2025年5月7日。

On April 3, 2025, Japan’s Ministry of Internal Affairs and Communications (MIC) solicited public comments on the draft report of the Committee on Next-Generation Mobile Communications Systems on the technical requirements for 5G mobile communication systems (26 GHz band/40 GHz band). The comment period is until May 7 2025.

 

Japan日本

日本經濟產業省和智慧財產局推出JC-STAR物聯網網路安全自願認證標籤

2025年3月25日，日本經濟產業省 (METI) 與資訊科技振興機構 (IPA) 宣佈啟動日本網路安全技術評估要求 (JC-STAR) 自願認證標籤計畫。該計畫適用於可以使用 IP 透過互聯網發送和接收資料的物聯網 (IoT) 設備，以及間接連接到互聯網的物聯網設備。該計畫分為四個產品類別，STAR-1和STAR-2標籤可透過自我聲明授予，STAR-3和STAR-4標籤則需經過協力廠商實驗室測試和評估後授予。

點擊此連結查看 METI 公告原文。

On March 25, 2025, Japan’s Ministry of Economy, Trade and Industry (METI) and the Information Technology Promotion Agency (IPA) announced the launch of the Japan Cybersecurity Technology Assessment Requirements (JC-STAR) voluntary certification label program. This program applies to Internet of Things (IoT) devices that can use IP to send and receive data over the internet, as well as IoT devices that are indirectly connected to the internet. The program is divided into four product categories, STAR-1 and STAR-2 labels can be granted through self-declaration, and STAR-3 and STAR-4 labels are awarded after third-party laboratory testing and evaluation.

The JC-STAR label contains a QR code that links to the labeled product’s website via IPA with details such as supplier information, product information, label information, safety information (any updates or vulnerabilities to the product), and contact information. An example of a label that contains a QR code is as follows:

The JC-STAR STAR-1 label is valid for 2 years, and the IPA will publish a list of labeled products in early May 2025. Conformance standards are currently being developed for STAR-2, STAR-3 and STAR-4 products.

Click this link to view the original METI announcement.

 

Mexico墨西哥

墨西哥IFT 發佈適用於 WLAN 裝置的 IFT-017-2023 勘誤表

2025 年 4 月 2 日，墨西哥政府發佈了 IFT-017-2023 勘誤表，更新了第 5.7.2 節的視訊頻寬 (VBW) 條目。 5725 MHz – 5850 MHz 頻段所需的最小頻道頻寬為「≥ 3 x RBW」。

On April 2, 2025, Mexico government published IFT-017-2023 errata updating the Video Bandwidth (VBW) entry for Section 5.7.2. The minimum channel bandwidth required for the 5725 MHz – 5850 MHz band is “≥ 3 x RBW”.

 

Mexico墨西哥

墨西哥IFT就新版IFT標籤生效日期的修訂展開公眾諮詢

[法規草案] 2024年10月2日，墨西哥聯邦電信局 (IFETEL) 批准對型式認可指南和IFT標籤使用準則的修改。修訂後的IFT標籤使用指南原定於2025年7月1日生效。 IFETEL於2025年4月11日就修訂後的IFT標籤使用指南的生效日期和範圍展開公眾諮詢，將原定的生效日期從2025年7月1日推遲至2027年7月1日。

點擊此連結查看原始公眾諮詢，評論期至 2025 年 5 月 2 日。

On October 2, 2024, Mexico’s Federal Telecommunications Agency (IFETEL) approved modifications to the the guidelines for the use of the type approval guide and the IFT seal. The revised guidelines for the use of the IFT sealwere originally scheduled to go into effect on July 1, 2025. IFETEL launched a public consultation on 11 April 2025 on the effective date and scope of the revised guidelines for the use of the IFT seal, postponing the original effective date from 1 July 2025 to 1 July 2027.

Click this link to view the original public consultation and the comment period is until 2 May 2025.

 

Mexico墨西哥

墨西哥就電子設備充電器進行公眾諮詢

[法規草案] 墨西哥參議院提出了一項關於電子設備充電器的倡議。

擬議的倡議旨在修改《聯邦電信和廣播法》第 191 條，旨在強制所有電子設備使用 USB-C 充電器。該倡議目前正處於公眾諮詢階段。

Mexico public consultation regarding chargers for electronic devices.

An initiative has been presented in the Senate regarding chargers for electronic devices.

The proposed initiative seeks to amend Article 191 of the Federal Telecommunications and Broadcasting Law to include a new provision (Section XXII).

This amendment aims to mandate the use of USB-C chargers for all electronic devices.

The initiative is currently in the public consultation stage. If accepted, it is expected to enter into force the day after its publication. In addition, a period of 180 days would be ordered to issue the corresponding NOM.

 

Paraguay巴拉圭

巴拉圭 CONATEL 發佈第 0148-2025 號決議，修改了國家頻率分配計畫 (PNAF)

巴拉圭國家電信委員會 (CONATEL) 於 2025 年 1 月 22 日透過第 0148-2025 號決議修改了國家頻率分配計畫 (PNAF)。根據該決議，3300-3700 MHz 將分配給 5G，但目前尚未有業者分配該頻段。

Paraguay CONATEL Publishes Resolución Directorio N° 0148-2025

The Comisión Nacional de Telecomunicaciones (CONATEL) of Paraguay modified the Plan Nacional de Atribución de Frecuencias (PNAF) on January 22, 2025, through Resolución Directorio N° 0148-2025. According to the Resolution, the 3300-3700 MHz will be allocated for 5G, however no carriers have been assigned this band yet.

 

Saudi Arabia沙烏地阿拉伯

自2025年2月12日起，供應商現在必須在SABER上註冊其ICT產品

通訊、太空和技術委員會 (CST) 和沙烏地阿拉伯標準、計量和品質組織 (SASO) 已合作透過過渡到 SASO SABER 平台來加強產品一致性評估。

自2025年2月12日起，ICT設備的型式核准 (即原本由CST頒發的 CITC證書) 和清關程式將透過「Saber平台」進行。因此，供應商現在必須在SABER上註冊其ICT產品，以獲得必要的合規認證。

The Communications, Space and Technology Commission (CST) and the Saudi Standards, Metrology and Quality Organization (SASO) have collaborated to enhance product conformity assessment by transitioning to the SASO SABER platform.

The procedures for type approval and customs clearance for ICT devices will be conducted through the “Saber Platform” starting from February 12, 2025. As a result, suppliers must now register their ICT products on SABER to obtain the necessary compliance certifications.

 

Singapore新加坡

新加坡發布新版消費者保護 (安全要求) 註冊計畫 (CPS) 資訊手冊

新加坡於2025年2月1日發布了新版消費者保護 (安全要求) 註冊計畫 (CPS) 資訊手冊，增加了自2024/2025年6月1日起生效的中度風險管製商品測試標準的新要求 (第4.1章)。

Singapore Enterprise released a new edition of the Consumer Protection (Safety Requirements) Registration Scheme (CPS) Information Booklet on February 1, 2025. Added are new requirements to test standards for medium-risk controlled goods with effect from June 1, 2024/2025 (chapter 4.1).

 

South Korea韓國

韓國MSIT發佈修訂頻率分佈表

2025年2月17日，科學技術資訊通訊部 (MSIT) 發佈關於修訂韓國頻率分佈表的科學技術資訊通訊部第2024-44號通知，並於同日生效。

South Korea MSIT Publishes Revised Frequency Distribution Table

On February 17, 2025, the Ministry of Science and ICT (MSIT) published under Ministry of Science and ICT Notice No. 2024-44 on the amendment of South Korea Frequency Distribution Table, which took effect on the same day.

 

South Korea韓國

RRA發布廣播及通訊設備等合格評定通知

韓國無線電研究所(National Radio Research Agency- RRA)於2025年4月25日發布廣播及通訊設備等合格評定通知第2025-2號，主要修訂內容如下，並於同日生效:

<附錄1>

3. 簡易無線電台、太空站、地球站的無線電設備、無線電探測用無線電設備以及其他商業無線電設備: 新增低軌道衛星通訊地球站無線電設備

<附錄7> 廣播、通訊設備等的格式符號的表示方法:

同步新增低軌道衛星通訊地球站無線電設備

法規參考: https://www.law.go.kr/admRulLsInfoP.do?chrClsCd=&admRulSeq=2100000258196

On April 25, 2025, the National Radio Research Agency (RRA) of Korea issued Notification No. 2025-2 on the Conformity Assessment of Broadcasting and Communication Equipment. The main amendments are as follows, which took effect on the same day.

<Appendix 1>
3. Radio equipment for simple radio stations, space stations, earth stations, radio equipment for radio detection, and other commercial radio equipment:

Addition of radio equipment for low Earth orbit (LEO) satellite communication earth stations.

<Appendix 7>
Method of Indicating the Format Symbols for Broadcasting and Communication Equipment:
Simultaneous addition of radio equipment for low Earth orbit (LEO) satellite communication earth stations.

Regulatory references: https://www.law.go.kr/admRulLsInfoP.do?chrClsCd=&admRulSeq=2100000258196

 

Thailand泰國

TISI發布便攜式浸入式加熱器符合泰國工業標準的法規草案

[法規草案] 2025年3月13日，TISI發布關於要求便攜式浸入式加熱器符合泰國工業標準的法規草案。該草案要求便攜式浸入式加熱器符合泰國工業標準 TIS 60335 第 2(74)-2565(2022)《家用及類似用途電器 – 安全 – 第 2-74 部分: 便攜式浸入式加熱器的特殊要求》。

該草案適用於家用和類似用途的便攜式電浸入式加熱器，其額定電壓不超過250V。

On 13 March 2025, TISI published a WTO document about draft Ministerial Regulation that mandates portable immersion heaters to conform to the Thai Industrial Standard TIS 60335 Part  2(74)-2565(2022) Household and Similar Electrical Appliances – Safety – Part 2-74: Particular Requirements for Portable Immersion Heaters.

This draft Ministerial Regulation applies to portable electric immersion heaters for household and similar purposes, their rated voltage being not more than 250 V.

 

Taiwan台灣

BSMI 及NCC更新認可的外國 EMC 測試實驗室名單及國內認可的電信設備測試實驗室名單

標準檢驗局 (BSMI) 及通訊委員會 (NCC) 已更新 BSMI 認可的外國 EMC 測試實驗室名單及國內認可的電信設備測試實驗室名單。

The Bureau of Standards, Metrology and Inspection (BSMI) and the National Communications Commission (NCC) of Taiwan has updated the List of EMC Testing Laboratories Recognized by BSMI in Foreign Countries, and the List of Domestic Recognized Telecommunication Equipment Testing Labs.

 

UK 英國

Ofcom 與民航局 (CAA) 發表聯合聲明，關於使用 978 MHz 頻譜作為無人機安全設備

2025 年 3 月 11 日，Ofcom 與民航局 (CAA) 發表了一份聯合聲明，關於使用 978 MHz 頻譜作為無人機安全設備。

這些安全裝置 (通用接入收發器) 使其他飛機知道無人機的位置。有了這種設備，無人機可以檢查風力渦輪機和電力線，看是否需要維修。

自 2025 年 3 月 11 日起，Ofcom 不再授權 PMSE 用戶在室外使用 978 MHz 頻譜，但他們可以繼續在室內使用該頻譜，並且 Ofcom 正在擴展 PMSE 使用者在室內和室外可用的其他頻率範圍 (包括 1015-1016 MHz、1044-10475-10475-1045 1104-1105 MHz)。因此PMSE 用戶將擁有比以前更多的頻譜。

On 11 March 2025 , Ofcom has published a joint statement with the Civil Aviation Authority (CAA) on the use of 978 MHz spectrum for safety devices on drones.

These safety devices (Universal Access Transceivers) make other aircraft aware of a drone’s position. They are required for some important applications, for example enabling innovation and efficiency in managing critical infrastructure. With this equipment, drones can, for instance, inspect wind turbines and power lines to see if repairs are needed.

This new authorisation will be incorporated in existing drone licence from 11 March 2025 . Most consumer drones do not need any Ofcom licence as they typically use licence-exempt spectrum. However, most commercial or advanced users, especially those wanting to use drones at long distance, need a licence from Ofcom and likely from the CAA.

The 978 MHz spectrum is used for drones internationally, and in the UK these frequencies have been shared between aeronautical use and low-power radio microphones in programme making and special events (PMSE) since 2016.

From 11 March 2025 , Ofcom no longer licenses 978 MHz spectrum for PMSE users in outdoor settings, but they can continue to use it indoors, and Ofcom is expanding the range of other frequencies that are available to PMSE users both indoor and outdoor (including 1015-1016 MHz, 1044-1045 MHz, 1075-1076 MHz and, 1104-1105 MHz). As a result, PMSE users will have more spectrum than before.

 

Ukraine烏克蘭

烏克蘭批准修改《低壓電氣設備技術法規適用國家標準清單》

此次修訂是為了與歐盟決議 (EU) 2024/2764 保持一致，涉及的產品包括螺紋燈座、電器配件的盒子和外殼、固定循環器、馬桶和電動車充電系統。

Ukraine approves amendment to the List of National Standards for the Purposes of Applying the Technical Regulations for Low-Voltage Electrical Equipment.

The amendment happens in order to align with EU DECISION (EU) 2024/2764, involved prducts are threaded lampholders, boxes and housings for electrical accessories, stationary circulators, toilets and electric vehicle charging systems.

 

Vietnam越南

越南科技部發佈公告修訂免許可設備清單

2025年3月31日，由原始通訊與媒體部 (MIC) 和科學技術部 (MOST) 合併而成的越南新科學技術部 (MST) 發佈了編號為01/2025/TT-BKHCN的公告，對2021年10月14日發佈的08/2021/TT-BTTTT公告進行了修訂。此修訂將原有的326.5kHz-340kHz無線充電頻段擴展至315kHz-400kHz，增加並更新了更多與6GHz頻段WLAN相關的技術需求。

本公告生效日期為2025年5月15日。

On 31 March 2025, the new Ministry of Science and Technology (MST) of Vietnam, which was formed by the merger of the former Ministry of Communications and Media (MIC) and the Ministry of Science and Technology (MOST), issued an announcement numbered 01/2025/TT-BKHCN amending the announcement 08/2021/TT-BTTTT issued on October 14, 2021. The revision expands the original 326.5kHz-340kHz wireless charging frequency band to 315kHz-400kHz, and adds and updates more technical requirements related to WLAN in the 6GHz frequency band.

The effective date of the announcement is May 15, 2025.

 

 

家用電器 House Appliances

Chile智利

SEC修改冰箱/冷櫃安全協議PE N°1/17:2023的實施時間，延遲至2026年1月1日之後執行

2025年4月24日，智利SEC 正式發佈決議N°31835，修改了冰箱/冷櫃安全協議PE N°1/17:2023的實施時間，延遲至2026年1月1日之後執行。

同時，此決議針對體系1認證的後續出貨抽樣測試的樣板要求也進行了修訂:

用於條款27.5和30的測試樣板，由原來的2個單位樣板要求改為1個單位的樣板要求。

On 24 April 2025，Chile SEC published Resolution N°31835 to extend the entry in force of PE N°1/17:2023 for refrigerator/ freezer to January 1^st, 2026

In addition, the same resolution modifies the QTY of samples for follow up testing in System 1: Replace in PE Protocol No. 1/17:2023, in CHAPTER II, Numeral 1.2.1.2, Table B, column 5, where it reads 2 units, with the following:

“1 unit, i.e. for Clause 27.5 and 30 tests are performed on one unit, they are not additional samples to those indicated in the Table”.

 

India印度

BEE發布《關於在電子商務平台和其他銷售點正確展示家用電器BEE星級標籤的指南》

BEE發布了《關於在電子商務平台和其他銷售點正確展示家用電器BEE星級標籤的指南》，適用於 BEE Star 能源效率計劃下的所有強制性和自願性設備。

BEE released the “Guideline on proper display of BEE Star Labels for appliances on E-commerce platforms and other point of sales”.  It applies to all mandatory and voluntary appliances under BEE Star energy efficiency scheme.

 

Philippines菲律賓

電風扇和洗衣機能源標籤強制執行

菲律賓能源部通知所有電風扇和洗衣機的經銷商和零售商，針對這些產品的執法活動將在註冊開始兩 (2) 年後開始。由於電風扇和洗衣機的 PELP 產品註冊於 2024 年 3 月 25 日開始，執法活動將暫定於 2026 年 3 月開始。此時間表可能會根據當地測試設施或 DOE 認可的測試實驗室的可用性，或是否存在重大利益相關者的擔憂而發生變化。

能源部 (DOE) 將在執法活動開始前至少六 (6) 個月發佈官方諮詢，以確保所有相關方都得到適當的通知和準備。

Enforcement of Energy Labels for Electric Fans and Clothes Washing Machines

Philippines Department of Energy would like to inform all dealers and retailers of Electric Fans and Clothes Washing Machines that enforcement activities for these products will begin two (2) years after the start of registration. Since PELP Product Registration for Electric Fans and Clothes Washing Machines started on 25 March 2024, enforcement activities will commence tentatively by March 2026. This timeline may change depending on the availability of local testing facilities or DOE-Recognized Testing Laboratories or if there are major stakeholder concerns.

​The Department of Energy (DOE) will issue an official advisory at least six (6) months before the start of enforcement activities to ensure that all concerned parties are properly informed and prepared.

 

Uruguay烏拉圭

烏拉圭更新製冷器具和空調器的能源效率標籤規則

烏拉圭公佈決議，在現行規則實施過程中設立過渡期，並規定就未來幾年將確定新的評估和認證標準的技術法規進行公眾諮詢。

Uruguay updated of the energy efficiency labelling of refrigeration appliances and air conditioners.

Uruguay published Resolutions establishing a transition period in the implementation of the current rules and provide for public consultation of technical regulations that will define the new evaluation and certification criteria in the coming years.

The Ministry of Industry, Energy and Mining has defined guidelines for updating the technical regulation of energy efficiency labelling of Domestic Use Refrigeration Apparatus through Resolution S/N of 30 December 2024, and air conditioners and heat pumps through Resolution S/N of 30 December 2024.

As the main aspects to be considered, the Resolutions state that:

Cooling equipment:

The conformity assessment of refrigeration equipment will continue to be carried out according to UNIT 1138:2011 until the EMI establishes otherwise, a fact that will not happen before 1 January 2027.

Within 12 months of 30 December 2024, the draft Technical Regulation of Electrical Refrigeration Apparatus for Domestic Use shall be put in public consultation, which shall establish the time limits and the forms for updating the conformity assessment procedure in accordance with UNIT 1138:2023.

Air conditioners:

Conformity assessment will continue to be carried out under UNIT 1170:2009 until the EMI establishes otherwise, a fact that will not happen before 1 July 2027.

Within 18 months, from 30 December 2024, the draft Technical Regulations on Air Conditioners and Domestic or Similar Heat Heat Permits shall be made available, which shall establish the time limits and ways for updating the conformity assessment procedure in accordance with UNIT 1170:2023.

 

 

燈具 / LED Luminaiaries/LED

Chile智利

SEC發佈關於用於公共照明的太陽能燈具 (太陽能區域泛光燈)和 用於道路和街道照明的太陽能燈具的附錄通知

SEC發佈WTO附錄:
1. 附錄 G/TBT/N/CHL/702/Add.1 電氣產品安全分析和/或測試協議 PE No. 5/33: 2024: 用於公共照明的太陽能燈具 (太陽能區域泛光燈)。
2. 附錄 G/TBT/N/CHL/701/Add.1 電氣產品安全分析和/或測試協議 PE No. 5/32: 2024: 用於道路和街道照明的太陽能燈具。
實施日期為 2025 年 12 月 31 日。

​SEC (Electricity and Fuel Board- Superintendencia de Electricidad y Combustibles) announces:

1. Addendum G/TBT/N/CHL/702/Add.1​ for Safety analysis and/or test protocol for electrical products PE No. 5/33:2024: Solar luminaires (solar area floodlights) for public lighting.

​2. Addendum G/TBT/N/CHL/701/Add.1​ for Safety analysis and/or test protocol for electrical products PE No. 5/32:2024: Solar luminaires for road and street lighting.

The implement date is December 31, 2025.

 

 

能源效率要求 Energy Efficiency Requirements

Argentina阿根廷

阿根廷發佈針對法規237/2024和法規438/2024更新決議

阿根廷發佈了WTO檔G/TBT/N/ARG/459/Add.1，根據工業和貿易秘書處 (SIyC) 第26/2025號決議，對文件G/TBT/N/ARG/459中的第438/2024號決議進行修訂，取代第三條、第七條、附件一及附件五。

本技術法規規定了需要使用電源運行或使用時消耗能源的新產品或電器的能源效率標籤的基本要求和特性。

Argentina published a WTO document G/TBT/N/ARG/459/Add.1, pursuant to Resolution No.  26/2025 of the Secretariat for Industry and Trade (SIyC), SIyC Resolution No. 438/2024, notified in document G/TBT/N/ARG/459, was amended, replacing Articles 3 and 7, Annex I and Annex V.

This Technical Regulation establish essential requirements and characteristics for the energy efficiency labelling of new products or appliances that require the use of a power source for their operation, or which consume energy for their use.

 

China中國

中國發佈關於電動車充電樁能源效率限定值及能源效率等級的規範

[法規草案] 2025年3月13日，中國發佈關於電動車充電樁能源效率限定值及能源效率等級的WTO通報。本標準規定了電動車充電樁的能源效率等級、能源效率限定值和測試方法，適用於具有電流控制和/或電壓控制的非車載傳導供電設備，包括直流供電設備 (模式4，連接方法C) 和交流供電設備 (模式3，連接方法B或C)，供電網路側額定電壓不超過1000 V (交流)，電動汽車側額定最大電壓不超過1000 V (交流)。

On 13 March 2025, China published a WTO Notification about minimum  allowable  values  of  energy  efficiency  and  energy efficiency grades for electric vehicle charging piles.

This document specifies the energy efficiency grades, minimum allowable values of energy efficiency, and testing methods of electric vehicle charging piles.

This document applies to off-board conductive power supply equipment with current control and/or  voltage control, including direct current (DC) power supply equipment (Mode 4, Connection Method C) and alternating current (AC) power supply equipment (Mode 3, Connection Method B or C), with a rated voltage not exceeding 1000 V (AC) on the power supply network side and a rated maximum voltage not exceeding 1000 V (AC) or 1500 V (DC) on the electric vehicle side.

This document does not apply to：

• Power supply equipment that only provides direct current (DC) power on the power supply network side;
• In-Cable Control and Protection Devices (IC-CPD) for Mode 2 charging;
• Integrated charging and energy storage devices that do not have charging functions when the energy storage function is disabled;
• Power supply equipment for automatic charging or top-contact charging.

 

Colombia哥倫比亞

哥倫比亞發佈能效產品RETIQ 法規2025草案

[法規草案] 近日哥倫比亞發佈了Proyecto de Resolución Modificación RETIQ – 2025，新增烤箱和電視，並修訂原管控產品 (空調、冰箱、洗衣機、燃氣熱水器等設備) 的測試，准入及標籤要求。

Colombia recently released the Proyecto de Resolución Modificación RETIQ – 2025, adding ovens and televisions, and revising the testing, market access and labeling requirements for the original controlled products (air conditioners, refrigerators, washing machines, gas water heaters, etc.).

 

Taiwan 台灣

修正「吹風機節能標章能源效率基準與標示方法」等12項行政規則

經濟部能源署於2025年3月21日公布修正「吹風機節能標章能源效率基準與標示方法」等12項行政規則，自即日生效。其中包括:

• 吹風機：能源效率值 (UER) 須達5%
• 燃氣爐：熱效率需達 49%，CO 不可超標
• 燃氣熱水器：熱效率 83%以上，CO 限制同上
• 電熱水器：限制每日熱損耗，依容量計算
• 組合音響：待機功率不得超過 1W
• 浴室排風扇：須符合指定能源效率值

每項產品都需標示測試結果與製造資訊，方便消費者辨識。標章申請需附測試報告; 未達標產品不得貼節能標章。詳情請參考此連結。

On 21 March 2025, ENERGY ADMINISTRATION, MOEA Order is hereby given, for the revision of some 12 criteria and methods. The Bureau of Energy, MOEA, has updated the energy label requirements for the following six product categories:

• Hair Dryers: Must achieve a UER (useful energy ratio) of at least 19.5%.
• Gas Cooktops: Thermal efficiency must be ≥ 49%. Carbon monoxide (CO) emissions must not exceed limits.
• Gas Water Heaters: Thermal efficiency must be ≥ 83%. CO emissions must meet safety standards (same as cooktops).
• Electric Water Heaters: Daily heat loss is limited, calculated based on tank capacity.
• Compact Audio Systems: Standby power consumption must not exceed 1W.
• Bathroom Ventilation Fans: Must meet the specified energy efficiency requirements.

All products must display test results and manufacturer/importer information to ensure transparency for consumers. Applications for the energy label must include relevant test reports. Products that do not meet the standards may not bear the energy label.

Please refer to this link for more details.

 

 

其他 / 多主题产品 Others / Products with Multiple Subjects

India印度

印度發布低壓開關設備和控制設備IS/IEC 60947系列4項產品特定指南

印度重工業部發布《電氣設備 (品質控制) 命令，2020》低壓開關設備和控制設備IS/IEC 60947系列4項產品特定指南。

該指南包括產品分組和抽樣與測試，以確保產品系列/範圍或分組的樣品數量最少。

官方公告請見以下連結:

– IS/IEC 60947: Part 3:2012:  Switches, disconnectors, switch disconnectors and fuse – Combination units

– IS/IEC 60947: Part 4: Sec 1: 2012: Electromechanical contactors and motor – Starters 

– IS/IEC 60947: Part 5: Sec 1: 2009: Control circuit devices and switching elements-Electromechanical control circuit device

– IS/IEC 60947: Part 5: Sec 5: 2016: Control circuit devices and switching elements-Electromechanical control circuit devices with mechanical latching functions

Ministry of Heavy Industries publishes 4 Product Specific Guidelines for IS/IEC 60947 series under Low Voltage Switchgear and Controlgear of 《Electrical Equipment (Quality Control) Order, 2020》.

The guidelines include Product Grouping and Sampling and Testing which ensure the minimum number of sample(s) in respect of a product series/range or group.
Please find the guidelines as below links:

– IS/IEC 60947: Part 3:2012:  Switches, disconnectors, switch disconnectors and fuse – Combination units

– IS/IEC 60947: Part 4: Sec 1: 2012: Electromechanical contactors and motor – Starters 

– IS/IEC 60947: Part 5: Sec 1: 2009: Control circuit devices and switching elements-Electromechanical control circuit device

– IS/IEC 60947: Part 5: Sec 5: 2016: Control circuit devices and switching elements-Electromechanical control circuit devices with mechanical latching functions

 

India印度

印度MNRE發布《2025 太陽能系統、設備和組件商品命令》中 太陽能光伏 (PV) 模組、儲存電池以及光電逆變器的的實施指南

MNRE發布太陽能光伏 (PV) 模組、儲存電池的以及光電逆變器的實施指南修訂標準及其細則。

主要亮點：

1) IS 14286 (第 1 部分): 2023 / IEC 61215-1: 2021

• 定義了 IS 14286 系列中包含的所有類型太陽能光電模組的一般要求，作為整個系列的主要參考標準。
• 根據 MNRE 的新 QCO，太陽能光電模組在標準測試條件 (STC) 下進行測試時必須滿足最低效率等級。因此，實驗室必須根據「模組構造描述」下的 QCO 指定模組的輸出 (以 W 為單位)、面積 (m²) 和計算效率 (以 ％ 為單位)。

2）IS 16270:2023

• 最大充電電流 I10A
• 包含鋰電池類型和其他電化學
• 納入鋰電池和電池組標準
• 納入長期容量
• 納入額定容量的容量需求

所有製造商必須在規定的時間內 (2025 年 7 月 27 日) 實施修訂後的標準和新的 QCO。

3) IS 16169 : 2014/ IEC 62116 : 2008

• 在現有標準 IS 16221 (第 2 部分): 2015/IEC 62109-2: 2011 中新增了 IS/IEC 61683: 1999 (測量效率的程序)
• 新準則的最後實施日期為2025年7月27日
• 光電系統的電源逆變器必須依照 IS/IEC 61683:1999 進行測試，並提供單獨的測試報告

官方公告:

– Implementation guideline for Solar PV modules

– Guidelines for implementing IS 16270: 2023

– Revised QCO for Power Inverters

MNRE has released the Guidelines for “ Implementation of Revised QCO《Solar Systems, Devices and Components Goods Order, 2025) for Solar Photovoltaic (PV) Modules, Storage battery and Photovoltaic Inverters. For the implementation of revised standards and details, please find the table below:

S. No.	Product	Existing IS standard	Revised Standard notified in QCO	Indian standard/Product
1.	Crystalline Silicon Terrestrial Photovoltaic (PV) modules (Si wafer based)	IS 14286: 2010/ IEC 61215: 2005	IS 14286 (Part 1): 2023/ IEC 61215 – 1: 2021	Design qualification and Type approval
			IS 14286 (Part 1/Sec 1): 2023/ IEC 61215-1-1: 2021	Special requirements for testing of crystalline silicon photovoltaic (PV) modules.
		IS/IEC 61730 – 1: 2004	IS/IEC 61730 – 1: 2016	Photovoltaic (PV) Module Safety Qualification Part 1 Requirements for Construction
		IS/IEC 61730 – 2: 2004	IS/IEC 61730 – 2: 2016	Photovoltaic (PV) Module Safety Qualification Part 2 Requirements for Testing
2.	Thin-Film Terrestrial Photovoltaic (PV) Modules [CdTe, a-Si, Cu (In,Ga)(S,Se)	IS 16077: 2013/ IEC 61646: 2008	IS 14286 (Part 1): 2023/ IEC 61215 – 1: 2021	Design Qualification and Type Approval Part 1 Test Requirements
			IS 14286 (Part 1/Sec 2): 2023/ IEC 61215-1-2: 2021	Special requirements for testing of thin film cadmium telluride (CdTe) based photovoltaic (PV) modules
			IS 14286 (Part 1/Sec 3): 2023/ IEC 61215-1-3: 2021	Special requirements for testing of thin- film amorphous silicon based photovoltaic (PV) modules
			IS 14286 (Part 1/Sec 4): 2023/ IEC 61215-1-4: 2021	Special requirements for testing of thinfilm Cu (In,Ga)(S,Se)2 based photovoltaic (PV) modules
		IS/IEC 61730 – 1: 2004	IS/IEC 61730 – 1: 2016	Photovoltaic (PV) Module Safety Qualification Part 1 Requirements for Construction
		IS/IEC 61730 – 2: 2004	IS/IEC 61730 – 2: 2016	Photovoltaic (PV) Module Safety Qualification Part 2 Requirements for Testing
3.	Storage battery	IS 16270: 2014	IS 16270: 2023	Secondary cells and batteries for solar photovoltaic application – General requirements and methods of test
4.	Utility –Interconnected Photovoltaic inverters	IS 16169 : 2014/ IEC 62116 : 2008	IS 16169 : 2019/ IEC 62116 : 2014	Utility-Interconnected Photovoltaic Inverters — Test Procedure of Islanding Prevention Measures

Key Highlights:

1) IS 14286 (Part 1): 2023 / IEC 61215-1: 2021:

• Defines the general requirements for all types of Solar PV modules included in the IS 14286 series, serving as the main reference standard for the entire series.
• As per the new QCO of MNRE, Solar PV Module must meet a minimum efficiency level when tested under Standard Test Conditions (STC). Accordingly, Labs must specify the module’s output (in W), area (m²), and calculated efficiency (in %) as per the QCO under the “Description of Module Construction.”

2) IS 16270:2023:

• Maximum Charge Current I10A
• Inclusion of Lithium Battery Type and other electrochemistry
• Inclusion of standards for Lithium Cells and Batteries
• Inclusion of long-duration capacity
• Inclusion of capacity requirement of rated capacity

All manufacturers are required to implement the revised standards and the new QCO within the stipulated timeline (July 27, 2025).

3) IS 16169 : 2014/ IEC 62116 : 2008

• Addition of IS/IEC 61683: 1999 (Procedure for measuring efficiency) with the existing standard IS 16221 (Part 2): 2015/ IEC 62109-2: 2011.
• The last date of implementation with the new standard is 27 July 2025.
• Power inverters for photovoltaic systems must be tested as per IS/IEC 61683:1999, with a separate test report provided.

The official notification:

– Implementation guideline for Solar PV modules

– Guidelines for implementing IS 16270: 2023

– Revised QCO for Power Inverters 

 

Malaysia馬來西亞

馬來西亞發佈電動車充電系統 (EVCS) 指南

馬來西亞發佈電動車充電系統 (EVCS) 指南GP/ST/No.54/2025。該指南描述以下內容：

1. a) 安裝電動車充電系統所需的手冊標準與規範；
2. b) 允許的充電器模式；
3. c) 需要合資格人員負責安裝 EVCS；
4. d) 對製造商、進口商、展示者、銷售者、廣告商的要求；和
5. e) 預防性維護程序。

Malaysia issued Guideline on electric vehicle charging system (EVCS). These Guidelines describes the following:

(a) manual standard and specification required for the installation of electric vehicle charging system;

(b) the permissible charger mode;

(c) requirement of competent person for EVCS installation;

(d) requirement for manufacturer, importer, person who displays, seller and advertiser; and

(e) procedures for preventive maintenance.

 

Thailand泰國

TISI發布關於抽水馬桶的電動馬桶座圈必須符合泰國工業標準的法規草案

[法規草案] 2025年3月13日，TISI發布抽水馬桶的電動馬桶座圈必須符合泰國工業標準的法規草案 。該草案規定抽水馬桶的電動馬桶座圈必須符合泰國工業標準 TIS 60335 第 2(84)-2566(2023)《家用及類似用途電器 – 安全 – 第 2-84 部分: 衛生間電器的特殊要求》。

該草案適用於抽水馬桶電動馬桶座圈和馬桶座蓋。

On 13 March 2025, TISI published a WTO document about draft Ministerial Regulation that mandates electric toilet seat for water closet to conform to the Thai Industrial Standard TIS 60335 Part 2(84)-2566(2023) Household and Similar Electrical Appliances – Safety – Part 2-84: Particular Requirements for Toilet Appliances.

This draft Ministerial Regulation applies to electric toilet seat for water closet and toilet seat cover.

 

Ukraine烏克蘭

烏克蘭批准對《機械法規協調標準清單》進行修訂。

此次修訂是為了與歐盟第 2024/1329 號決定保持一致。協調標準適用於潛在爆炸性環境中的爆炸預防和保護、雷射設備、控制系統的安全相關部件、塑膠和橡膠製造機械、垃圾車、飛機地面支援設備、自行式工業貨車及其係統、電動自行車、冬季運動或旅遊用傳送帶、步行控制貨車、用於榫接和成型的木工機械、農業和林業拖拉機、商用包裝設備、商用空調包裝設備、商用空調和手動設備。

Ukraine approves amendment to Harmonised Standard List of Machinery Regulation. The amendment happens in order to align with EU DECISION (EU) 2024/1329.

The harmonised standards are for explosion prevention and protection in potentially explosive atmospheres, laser equipment, safety-related parts of control systems, plastics and rubber manufacturing machines, refuse trucks, aircraft ground support equipment, self-propelled industrial goods vehicles and their systems, electric bicycles, conveyor belts for winter sports or tourism use, pedestrian-controlled goods vehicles, woodworking machines for tenoning and profiling, agricultural and forestry tractors, commercial vacuum packaging equipment, commercial refrigeration and ice makers, grass shears and hand-operated motorised garden machinery.

 

Vietnam越南

越南提出電動車充電設備國家技術法規

[法規草案] 該國家技術法規草案規定了用於為電動道路車輛充電的電動汽車傳導供電設備的安全要求，其額定供電電壓高達交流 1000 V 或直流 1500 V，額定輸出電壓高達交流 1000 V 或直流 1500 V。電動道路車輛 (EV) 包括所有道路車輛，包括插電式混合動力道路車輛 (PHEV)，其全部或部分能量來自車載可充電儲能系統 (RESS)。該國家技術法規草案適用于在越南從事電動車供電設備生產、組裝、進口和貿易的組織和個人。

該草案正在徵求意見。擬採用日期為2025年4月28日，擬實施日期為2025年6月15日。

Vietnam proposes National technical regulation on electric vehicle charging equipment.

This  draft  national  technical  regulation  stipulates  the  safety requirements for EV conductive supply equipment used for charging electric road vehicles, with a rated supply voltage up to 1 000 V AC or up to 1 500 V DC, and a rated output voltage up to 1 000 V AC or up to 1 500 V DC. Electric road vehicles (EV) include all road vehicles,  including  plug-in  hybrid  road  vehicles  (PHEV),  that  derive  all  or  part  of  their energy from on-board rechargeable energy storage systems (RESS). This draft national technical regulation applies to organizations and individuals involved in production, assembly, import, and trading of EV conductive supply equipment in Vietnam.

The draft is recieving comments. The proposed adoption date is Apr-28 of 2025, proposed implementation date is Jun-15 of 2025.

 

資訊 / 電信 ITE / Telecom

Brazil巴西

巴西ANATEL發佈檔澄清5150-5350 MHz頻段在車輛使用方面的室內環境定義 

巴西ANATEL發佈第81/2025號官方函件，澄清5150-5350 MHz頻段，特別是在車輛使用方面的室內環境定義。

主要更新內容：

• 允許使用: 5150-5350 MHz頻段 (WLAN B1/B2) 僅限於完全封閉的車輛 (例如: 汽車、卡車) 。
• 禁止使用: 開放式車輛 (例如：摩托車、嘟嘟車和敞篷車) 不得使用。

Brazil ANATEL issued last week the Official Letter 81/2025 which clarifies the definition of indoor environments for the 5150-5350 MHz frequency range, particularly for vehicular use.

Key updates:

• Permitted Use: The 5150-5350 MHz band (WLAN B1/B2) is allowed only in fully enclosed vehicles (e.g., cars, trucks).
• Prohibited Use: Open vehicles like motorcycles, tuk-tuks, and convertibles are restricted.

 

Chile智利

智利發佈家用和辦公室用單功能和多功能雷射和噴墨印表機的安全認證分析和/或認證測試協議 PE No. 8/7:2024

[法規草案] 2025 年 1 月 7 日，智利發佈安全認證分析和/或認證測試協議草案 PE No. 8/7:2024，並預計於2026年6月30日實施。該通報議定書規定了電氣產品，即家用和辦公室用的單功能和多功能雷射和噴墨印表機的安全認證程式。

The Republic of Chile hereby advises that draft safety analysis and/or certification test protocol PE No. 8/7:2024 was published in the Official Journal on 7 January 2025 through Official Circular No. 263828 of 27 December 2024 of the Ministry of Energy/Electricity and Fuel Board.

The notified Protocol establishes the safety certification procedure for electrical products, namely single-function and multifunction laser and inkjet printers for household and office use.

 

China中國

中國工業和資訊化部 (MIIT) 發佈《雷達無線電管理規定》

2025 年 2 月 14 日，中國工業和資訊化部 (MIIT) 出台了《雷達無線電管理規定》，以加強頻率分配、設備標準和行業合規性。這些規則將於 2026 年 1 月 1 日生效，並將影響雷達無線電設備的製造、銷售、進口和維護。

On February 14, 2025, China’s Ministry of Industry and Information Technology (MIIT) introduced the Radar Radio Management Regulations to enhance frequency allocation, equipment standards, and industry compliance. These rules will take effect on January 1, 2026 and will impact manufacturing, sales, import, and maintenance of radar radio equipment.

 

Egypt埃及

埃及發佈通知，生產商和進口商有六個月的過渡期以遵守埃及標準 ES 2501-1“音訊/視頻、資訊和通信技術設備 – 第 1 部分: 安全要求”

2025年2月11日，埃及發佈了 WTO 通知附錄，涉及部長令第 7/2025 號的通知，該法令為生產商和進口商提供了六個月的過渡期，以遵守埃及標準 ES 2501-1“音訊/視頻、資訊和通信技術設備 – 第 1 部分: 安全要求”。

On 11 February 2025, Egypt released WTO Notification Addendum that concerns the notification of the Ministerial Decree No. 7 /2025 that gives the producers and importers a six-month transitional period to abide by the Egyptian

Standard ES 2501-1 “Audio/video, information and communication technology equipment – Part 1:

Safety requirements “. This standard cancels and supersedes the Egyptian standard ES 2501.

It should be noted that the draft of Egyptian standard ES 2501 was formerly notified in

G/TBT/N/EGY/157/Add.8 dated 9 October 2024, and the Ministerial Decree No. 241/2016 which was formerly notified in G/TBT/N/EGY/157 dated 15 August 2016, mandated among others the earlier version of this standard.

Worth mentioning is that this standard adopts the technical content of IEC 62368-1/2023.

 

Hong Kong香港

香港發佈2025年版頻率劃分表

香港於2025年1月21日發佈2025年版頻率劃分表。

On 21 January 2025, Hong Kong publishes 2025 version Table of Frequency Allocations.

 

Hong Kong香港

香港通訊管理局澄清 6GHz Wi-Fi 設備在 HKCA 1081 規範下的最新認證規則

香港通訊管理局 (OFCA) 最近通過電子郵件澄清 6GHz Wi-Fi 設備在 HKCA 1081 規範下的最新認證規則:

• 設備必須符合 ETSI EN 303 687 標準。
• 僅允許使用 5,945MHz-6,425MHz 頻段，5,925MHz-5,945MHz 禁止使用。
• 所有測試報告、證書和製造商聲明中，設備的最低運作頻率必須標示為 5,945MHz。

The Hong Kong Communications Authority (OFCA) recently through e-mail has clarified the latest certification rules for 6GHz Wi-Fi devices under the HKCA 1081 specification:

• Devices must comply with ETSI EN 303 687.
• Only the 5,945MHz-6,425MHz band is allowed; 5,925MHz-5,945MHz is prohibited.
• All reports, certificates, and manufacturer statements must specify 5,945MHz as the lower operating frequency.

 

India印度

印度發佈《2025 年電信 (標準、合格評定和認證) 規則》公告草案

[法規草案] 印度於2025年1月29日發佈《2025 年電信 (標準、合格評定和認證) 規則》公告草案，實施日期尚未確定。

On 29 January 2025, India published draft Gazette Notification regarding “Telecommunications (Standards, Conformity Assessment and Certification) Rules, 2025”

The implementation date is not determined yet.

 

Indonesia印尼

印尼發佈2025年第46號部長令，為無線電力傳輸 (WPT) 設備制定新的技術標準

印尼通訊和數位部 (KOMDIGI) 正式頒佈了2025年第46號部長令 (KM)，為無線電力傳輸 (WPT) 設備制定了新的技術標準。該法規取代先前的 KM 260/2024，自 2025 年 2 月 18 日起生效。

KM KOMDIGI No. 46/2025 中的關鍵更新:

1. WPT 設備強制輻射測試
2. WPT設備的新頻段
3. 測試報告接受及過渡期

The Indonesian Ministry of Communication and Digital (KOMDIGI) has officially issued Ministerial Decree (KM) No. 46 of 2025, which establishes new technical standards for Wireless Power Transmission (WPT) devices. This regulation replaces the previous KM 260/2024 and has been in effect since February 18, 2025.

The introduction of this updated regulation is aimed at ensuring the safety, efficiency, and compliance of WPT devices with the latest technological advancements and international standards. As wireless power transmission technology continues to evolve, it is crucial for manufacturers, importers, and distributors of WPT devices to adhere to the new regulatory framework to maintain legal market operations in Indonesia.

Key Updates in KM KOMDIGI No. 46/2025

To provide better guidance and clarity for industry players and stakeholders, here are the main updates introduced in this new regulation:

1. Mandatory Radiated Testing for WPT Devices

One of the most significant changes introduced in KM KOMDIGI No. 46/2025 is the requirement for all Wireless Power Transmission (WPT) devices to undergo radiated testing.

This mandatory testing is implemented to ensure that WPT devices do not cause harmful interference to other electronic and communication systems. It also helps in maintaining efficient power transmission while complying with safety regulations.

Manufacturers and importers must conduct radiated emissions tests at certified laboratories before submitting their devices for official certification. This ensures that each product meets the technical and safety requirements set by the government before being legally distributed in Indonesia.

2. New Frequency Bands for WPT Devices

The updated regulation expands the frequency spectrum allocated for Wireless Power Transmission. The new decree introduces three additional frequency bands specifically designated for WPT devices:

🔹 315-405 kHz – Suitable for low-frequency wireless power applications, including industrial and commercial usage.
🔹 1700-1800 kHz – Designed for mid-range power transmission applications, ensuring stable performance for various wireless charging solutions.
🔹 13.553-13.567 MHz – Allocated for high-frequency wireless charging applications, commonly used in fast-charging systems and high-efficiency power transfer devices.

By providing these additional frequency allocations, the Indonesian government aims to improve the efficiency of wireless power transmission systems while reducing potential interference with other telecommunication services.

Manufacturers and developers of WPT technology must ensure that their devices operate within these specified frequency ranges to comply with the new standards.

3. Test Report Acceptance and Transition Period

To facilitate a smooth transition from the previous regulatory framework (KM 260/2024) to the newly established KM KOMDIGI No. 46/2025, a special provision has been introduced for test reports.

Test reports issued before February 18, 2025, under the previous decree, may still be used for telecommunication equipment certification applications, as long as they:
🔹 Are still valid and relevant to the latest regulatory standards.
🔹 Do not conflict with the new technical requirements specified in KM KOMDIGI No. 46/2025.
🔹 Have been conducted by accredited testing laboratories recognized by the Indonesian government.

After the transition period ends, all applications for certification must strictly comply with the updated testing and technical requirements to obtain approval from SDPPI/DJID.

 

Indonesia印尼

印尼DJI宣佈 2025 年第 12 號法令的過渡期為六個月

2025 年 2 月 21 日，印尼數字基礎設施總局 (DJID，前身為 SDPPI) 在其網站上宣佈，通信和數位事務部長關於電信設備/無線電頻譜和無線電局域網設備技術標準的 2025 年第 12 號法令已於2025年 1 月 15 日生效。對於運行在 2400-2483.5 MHz、5150-5250 MHz、5250-5350 MHz 和 5725-5825 MHz 的產品，將提供長達 6 個月的過渡期，在此期間可以使用原始的 2019 年第 2 號 SDPPI 法規。

On February 21, 2025, Indonesia’s Directorate General for Digital Infrastructure (DJID, formerly SDPPI) announced on its website that the Minister of Communications and Digital Affairs Decree No. 12 of 2025 on Technical Standards for Telecommunication Equipment/Equipment for Radio Spectrum and Radio Local Area Network Based on Class Licenses has entered into force on January 15, 2025. For products operating at 2400-2483.5 MHz, 5150-5250 MHz, 5250-5350 MHz and 5725-5825 MHz, a transition period of up to 6 months will be provided, during which the original SDPPI Regulation No. 2 of 2019 can be used.

 

Israel以色列

以色列強制性標準 SI 62368 第 1 部分和自願性標準 SI 60950 第 22 部分的修訂 (涉及音訊/視訊、資訊和通訊技術設備) 已被 SI 62368 第 1 部分取代

以色列發布WTO通知附錄 – 強制性標準 SI 62368 第 1 部分和自願性標準 SI 60950 第 22 部分的修訂 (涉及音訊/視訊、資訊和通訊技術設備) 已被 SI 62368 第 1 部分取代。

修訂版本於 2025 年 1 月 20 日在以色列官方公報第 11719 號政府公告部分公佈。

本次修訂生效後，至2026年1月31日，舊標準及修訂標準均將適用。

Israel released WTO Notification Addendum. The revision of the Mandatory Standard SI 62368 part 1 and the voluntary standard SI 60950 part 22, dealing with audio/video, information and communication technology equipment, was replaced with SI 62368 part 1.

The revision was published on 20 January 2025 in Israel Official Gazette, Section of Government Notices no 11719.

The old  standards will still apply when this revision enters force until 31 January 2026. During this transition period, products may be tested according to either standard.

 

Japan日本

日本總務省宣佈FM廣播頻帶上限將從95MHz變成99MHz

[法規草案] 日本向WTO發佈關於部分修改《無線電設備管理條例》和《特定無線電設備技術標準符合性認證條例》的通知。FM廣播頻段上限將從95MHz變成99MHz。

修改的原因是為了滿足現有FM頻段無法滿足的需求，例如，設置FM中繼站以消除AM廣播的聽力損失點並在災難期間繼續廣播，以及由於AM廣播設備老化而轉換為FM廣播。

Japan ​released a WTO Notification about partial amendment of the Regulation for Radio Equipment and the Ordinance on Technical Standards Conformity Certification of Specified Radio Equipment.

The upper limit of the frequency band for FM broadcasting will be changed from 95 MHz to 99MHz.

The reason for the amendment is to meet the demand that cannot be satisfied by the current FM frequency band, such as establishing FM relay stations to eliminate hearing loss spots from AM radio broadcasting and keep broadcasting during disasters, and converting to FM broadcasting because of the aging AM broadcasting facilities.

 

Taiwan 台灣

國家通訊傳播委員會發佈修正「應經核准之電信管制射頻器材」

國家通訊傳播委員會於2025年2月3日發佈修正「應經核准之電信管制射頻器材」，並自即日生效。

The National Communications Commission issued the “Amendment to the Regulations on Telecommunications Regulated Radio Frequency Equipment that Must be Approved” on February 3, 2025, and it was taken effect immediately.

 

Taiwan 台灣

數位發展部發佈修正「無線電頻率供應計畫」

數字發展部於2025年年2月13日發佈修正「無線電頻率供應計畫」，並自即日生效。

MINISTRY OF DIGITAL AFFAIRS Notice is hereby given, for the amendment of “Radio Frequency Supply Plan” (amendment became effective from 13th, February 2025).

 

Vietnam越南

越南發佈ICT產品法規標準清單及適用產品法規標準範圍

越南資訊通信部發佈第178/QD-BTTTT號決定，電信部指定的電信品質檢測中心應依本決定進行檢測。該決定將取代第 669/QD-BTTTT 2023 號決定，並自 2026 年 4 月 19 日起生效。

Vietnam Ministry of Science and Technology issued Decision No. 178/QD-BTTTT of the Ministry of Information and Communications: Appoint the Telecommunications Quality Measurement Center under the Telecommunications Department to conduct testing within the designated scope.

The designated Telecommunications Quality Measurement Center under the Department of Telecommunications shall carry out testing according to this Decision.

This decision will replace Decision 669/QD-BTTTT 2023 and enter into force since Apr-19 of 2026.

 

Vietnam越南

越南頒佈《家用電氣裝置及類似安裝系統用電氣設備國家技術法規QCVN 25:2025/BKHCN》

2025年2月14日，越南科技部 (MOST)發佈第01/2025/TT-BKHCN號通告，並推出新的國家技術法規QCVN 25:2025/BKHCN，該法規適用於家用和類似用途的電氣設備。

• 自 2025 年 4 月 1 日起: 鼓勵製造和貿易電氣設備的組織和個人自願應用 QCVN 25:2025/BKHCN。
• 自2027年4月1日起: QCVN 25:2025/BKHCN附錄中的電氣設備在市場上流通前必須完全符合本標準的規定 (強制應用)。

QCVN 25:2025/BKHCN 的適用範圍見下表。

On February 14, 2025, the Ministry of Science and Technology officially issued Circular No. 01/2025/TT-BKHCN attached to the Technical Regulation QCVN 25:2025/BKHCN on electrical equipment for household electrical installations and similar electrical systems .

• From April 1, 2025: Encourage organizations and individuals manufacturing and trading electrical equipment to voluntarily apply QCVN 25:2025/BKHCN.
• From April 1, 2027: Electrical equipment in Appendix A and Appendix B of QCVN 25:2025/BKHCN must fully comply with the provisions of this standard before being circulated on the market (mandatory application).

Refer to below table for products in scope.

TT	產品名稱 Product Name	產品代碼 ( HS ) Product code (HS)	適用標準 Applicable standards
1.	額定電流不超過63A的家用及類似用途過電流斷路器 (MCB) Overcurrent circuit-breakers for household and similar purposes (MCB) with rated current not exceeding 63 A	85362011 85362012 85362013 85362091 85362099	TCVN 6434-1:2018 (IEC 60898-1:2015)
2.	家用及類似用途額定電流不超過63A的帶過電流保護的剩餘電流動作斷路器 (RCBO) Residual current operated circuit-breakers with overcurrent protection for household and similar purposes (RCBO) of rated current not exceeding 63 A	85365020	TCVN 6951-1:2007 (IEC 61009-1:2003)
3.	額定電流不超過32A的家用電源插座 Household electrical sockets with a rated current not exceeding 32 A	85366992 85366999	TCVN 6188-1:2007 (IEC 60884-1:2002) TCVN 6188-2-3:2016 (IEC 60884-2-3:2006) TCVN 6188-2-6:2016 (IEC 608884-608
4.	額定電流不超過32A的家用電器插頭 Household electrical plugs with a rated current not exceeding 32 A	85366992 85366999	TCVN 6188-1:2007 (IEC 60884-1:2002) TCVN 6188-2-1:2008 (IEC 60884-2-1:2006)
5.	額定電流不超過32A的家用插座轉接器 Socket adapter for household use with a rated current not exceeding 32 A	85366992 85366999	TCVN 6188-1:2007 (IEC 60884-1:2002) TCVN 6188-2-5:2016 (IEC 60884-2-5:1995)
6.	額定電流不超過 32 A 的家用延長線 Extension cords for household use with a rated current not exceeding 32 A	85369094 85369099	TCVN 6188-1:2007 (IEC 60884-1:2002) TCVN 6188-2-7:2016 (IEC 60884-2-7:2013)
7.	額定電流不超過20A的家用電氣開關 Electrical switches for household use with a rated current not exceeding 20 A	85365061 85365069	TCVN 6480-1:2008 (IEC 60669-1:2007)
8.	家用及類似用途額定電流不超過63A的無過電流保護的剩餘電流操作斷路器 (RCCB) Residual current operated circuit-breakers without overcurrent protection for household and similar purposes (RCCB) with rated current not exceeding 63 A	85365020	TCVN 6950-1:2007 (IEC 61008-1:2006)

 

 

家用電器 House Appliances

Chile智利

關於PE N°1/17/1& -2:2022 for Refrigerator, freezers, or refrigerator-freezer的過渡期

關於PE N°1/17/1& -2:2022 for Refrigerator, freezers, or refrigerator-freezer.  能效標籤及證書過渡期的使用通知:

• 最新適用協議版本: PE N°1/17/2:2022
• 根據先前PE N°1/17/2:2015頒發的EE證書，其有效期截至2024年11月30日的必須根據最新協定PE N°1/17/2:2022進行更新
• 根據先前PE N°1/17/2:2015頒發的EE證書，有效期自2024年12月1日起的，首次本地銷售(進口商和本地製造商) 將延長至2026年1月1日，後續本地銷售商的銷售期限將延長至2026年10月31日
• 市場上允許標貼根據PE N°1/17/2:2015獲得的EE標籤的產品，截止到2026年10月31日。
• 自2026年11月1日起，市場上銷售的所有相關產品必須根據PE N°1/17/2:2022進行認證和貼上新的EE標籤。

The grace period about PE N°1/17/1& -2:2022 for Refrigerator, freezers, or refrigerator-freezer:

• The applicable protocol for refrigerators, freezers and refrigerators-freezers is PE N°1/17/2:2022.
• EE Approvals issued under PE N°1/17/2:2015 with expiration date until 30.11.2024 must be renewed under PE N°1/17/2:2022.
• EE Approvals issued under PE N°1/17/2:2015 with expiry date as from 01.12.2024, it will be extended until 01.01.2026 for the first local selling (importers and local manufacturers), and it will be extended until 31.10.2026 for the selling of the subsequent local sellers.
• It will be allowed to exist into the market products with EE Label obtained under PE N°1/17/2:2015 until 31.10.2026.
• As from 01.11.2026 all products to be sold into the market must to be certified and must have the new EE Label according to PE N°1/17/2:2022.

 

Chile智利

智利發佈咖啡磨機和穀物研磨機的安全認證分析和/或測試認證協議PE No.1/42:2024

[法規草案] 2025 年 1 月 7 日，智利發佈關於電氣產品安全認證分析和/或測試協議 (PE No.1/42:2024)，並預計於2026年1月2日實施。該協議依據國際電子電機委員會 (IEC) 標準No.60335-2-14:2019-03的範圍和適用領域，制定了家用及類似用途料斗容量不超過500克的咖啡磨機和料斗容量不超過3公升的穀物研磨機的認證程序。

The Republic of Chile communicates that in relation to the Safety analysis and/or test protocol (PE No.1/42:2024) for electrical products, this was published in the Official Gazette on January 7, 2025, by Office No. 263828 of 27 of 27 December 2024, of the Ministry of Energy/Electricity and Fuel Board.

The notified protocol establishes the certification procedure for coffee mills not exceeding 500 g hopper capacity and grain grinders not exceeding 3L hopper capacity for household and similar purposes, in accordance with the scope and field of application of International Electrotechnical Commission (IEC) Standard No.60335-2-14:2019-03.​

 

China中國

中國發佈家用電冰箱耗電量限定值及能效等級徵求意見稿

[法規草案] 本文件規定了家用電冰箱的能耗最大允許值、能源效率等級、測試方法和文件實施要求。本文件適用於採用電機驅動壓縮或半導體製冷的家用電冰箱、儲酒櫃、可移動車載製冷器具。

China released a document collecting opinions of the standard of Maximum allowable values of the energy consumption and energy efficiency grade for household refrigerators.

This document specifies the maximum allowable values of the energy   consumption,   energy   efficiency   grades,   test   methods   and   document implementation requirements of household refrigerators.This document applies to household refrigerators, wine storage cabinets, and removable vehicle   refrigeration   appliances   with   motor-driven   compression   or   semiconductor refrigeration.

 

Côte d’Ivoire 象牙海岸

象牙海岸發佈通知，空調、冰箱和電燈應遵守能效標籤新規

象牙海岸能源總局向空調、冰箱和電燈分銷商和經銷商發佈通知：

根據通知編號 435/MMPE/MCI/DGT，需要貼上能源標籤的空調、冰箱和電燈應通過貼標籤程式。分銷商和經銷商應在 2025 年 7 月 15 日截止日期前聯繫能源總局進行能源分類程式。

在此截止日期之後，沒有監管能源標籤的分銷商和經銷商將受到處罰。

Côte d’Ivoire Directorate-General for Energy publishes Notice to Distributor and Dealer of Air-Con, Fridge-Freezer and Electric Lamp:

For Air-Con, Fridge-Freezer and Electric Lamp subject to energy labelling according to Notice No.435/MMPE/MCI/DGT, shall go through proper procedure for labelling.

The distributor and dealer shall contact Directorate-General for Energy to proceed energy classification procedure by Deadline Jul-15 of 2025.

After this deadline, there will be sanction to distributor and dealer who does not have regulatory energy label.

 

Mexico墨西哥

墨西哥發佈大容量單元式空調NOM標準草案

[法規草案] 2025年1月29日，墨西哥向WTO通報墨西哥官方標準草案PROY-NOM-035-ENER-2024，該草案規定了單元式空調的最低能源效率水準、測試方法、標記要求和合格評定程序。

Mexico released a WTO document about draft Mexican Official Standard PROY-NOM-035-ENER-2024: Energy efficiency of unit-type air conditioners. Limits, test methods and labelling.

The notified draft Mexican Official Standard PROY-NOM-035-ENER-2024 establishes the minimum energy efficiency levels, test method, marking requirements and conformity assessment procedure.

• It applies to self-contained “unit-type” (“package-unit”) air conditioners, with nominal cooling capacities of between 19,050 W (65,000 BTU/h) and 70,340 W (240,000 BTU/h), with or without reverse cycle, air-cooled, powered by electricity and operated by mechanical compression, equipped with a one-speed (fixed G/TBT/N/MEX/542- 2 -capacity) compressor, a variable frequency or refrigerant flow (proportionally controlled capacity) compressor or a multistage (staged capacity) compressor and an air-cooled evaporator coil, which are imported into or manufactured or marketed within the United Mexican States.
• The following are excluded from the scope of this draft Mexican Official Standard:

–              Split-type central air conditioners.

–              Water- or evaporative-cooled air conditioners.

 

Israel以色列

以色列強制性標準 SI 900 第 2.2 部分 (涉及吸塵器和吸水清潔設備) 的修訂已被 SI 60335 第 2.2 部分取代

以色列發布WTO通知附錄 – 強制性標準 SI 900 第 2.2 部分 (涉及吸塵器和吸水清潔設備) 的修訂已被 SI 60335 第 2.2 部分取代。

修訂版本於 2025 年 2 月 3 日在以色列官方公報第 11743 號政府公告部分公佈。

自本次修訂生效之日起至2026年8月3日，舊標準和修訂標準均將適用。

Israel released WTO Notification Addendum. The revision of the Mandatory Standard SI 900 part 2.2, dealing with vacuum cleaners and water-suction cleaning appliances, was replaced with SI 60335 part 2.2.

The  revision  was  published  on  3  February  2025  in  Israel  Official  Gazette,  Section  of  Government Notices no 11743.

The old and revised standards will apply from when this revision enters force until 3 August 2026. During this transition period, products may be tested according to either standard.

 

Mexico墨西哥

[法規草案] 2025年2月5號墨西哥–能源部–國家能源有效利用委員會–能源資源保護和合理利用國家標準化諮詢委員會 (CCNNPURRE) 發佈了PROY-NOM022ENER/SE2024, Eficiencia energética y requisitos de seguridad al usuario para aparatos de refrigeración comercial autocontenidos. Límites, métodos de prueba y etiquetado.( Draft-NOM022ENER/SE2024，獨立商用製冷設備的能源效率和使用者安全要求。限制、測試方法和標籤)的公眾諮詢。

意見收集截止日期自發佈後的60天，通過及生效日期待定。

The National Commission for the Efficient Use of Energy announces the PROY-NOM-022-ENER/SE-2024, which is to establish the maximum limits for electrical energy consumption, the test method, the marking requirements, and the conformity assessment procedure.​

Proposed date of adoption:  60 days from notification

Proposed date of entry into force:  to be determined

 

Saudi Arabia 沙烏地阿拉伯

SASO發佈洗衣機和冰箱性能測試標準草案

[法規草案] SASO 於2月25向WTO提交了Draft SASO 2885:2025 & Draft SASO 2892:2025 ，電動洗衣機、洗乾一體機和冰箱、冷櫃性能和標籤要求草案。

公眾諮詢期為發佈後60天。建議的通過和生效日期是在官方憲報公佈之日起2年後。

On 25 February 2025, Saudi Arabia published WTO Notification about draft SASO 2885:2025 – Electrical Clothes Washing Machines & draft SASO 2892:2025 – Refrigerators, Refrigerator- Freezers And Freezers Performance Requirements and Labelling.

Final date for comments: 60 days from notification

Proposed date of adoption: To be determined

Proposed date of entry into force: The Proposed date of adoption and entry into force is 2 years after the date of publication in the official Gazette.

 

Switzerland瑞士

瑞士發佈《能源效率條例 (EnEV)》修訂草案

[法規草案] 瑞士聯邦委員會3月21號發佈了《能源效率條例 (EnEV)》修訂草案，涉及系列生產設備、車輛和家電的能效要求。

Switzerland published a WTO Notification about draft revision of the ordinance on energy efficiency.

Products covered: Cold appliances (Fridges and Freezers); household washing machines; household tumble driers; household dishwashers; electronic displays; local space heaters; refrigerating appliances with a direct sales function; smartphones, mobile phones other than smartphones, cordless phones and slate tablets; ventilators; Stand-by.

Proposed date of adoption:  1 June 2025

Proposed date of entry into force:  1 July 2025

 

Taiwan 台灣

經濟部能源署 預告「電冰箱容許耗用能源基準與能源效率分級標示事項、方法及檢

查方式」部分規定及第5點附表5修正草案。

[預告修正] 2025年1月22日，為持續提升電冰箱產品之能源效率、引導業者研發及生產高效率產品，爰擬具本規定修正草案，其修正要點如下:

1. 修正電冰箱容許耗用能源基準及能源效率分級基準表 (修正規定第二點、第五點附表五)
2. 修正能源效率符合型式聲明書，增訂廠商願負切結責任相關文字 (修正規定第四點)
3. 新增廠商陳列或銷售電冰箱時，得以其他方式揭露能源效率分級標示圖 (修正規定第六點)
4. 本規定第二點已明定抽測結果判定原則，刪除重複規定並酌修文字 (修正規定第十一點)

通知截止日期为 2025 年 3 月 22 日，自通知之日起 60 天。詳情請參考此草案。

On 22 January 2025, MINISTRY OF ECONOMIC AFFAIRS Notice is hereby given, to commence a period of public comments for the draft amendment on partial provisions and Appendix 5 of Paragraph 5 of “Requirements on Minimum Energy Performance Standard, Energy Efficiency Rating Labelling and Inspection for Refrigerators” Notification deadline is 22th March 2025, 60 days from Notification.

Please see the draft.

 

 

燈具 / LED Luminaiaries/LED

Taiwan 台灣

台灣頒布《具標準互連協定通訊埠發光二極體平板燈具節能標章能源效率基準與標示方

法》

經濟部能源署 訂定「具標準互連協定通訊埠發光二極體平板燈具節能標章能源效率基準與標示方法」，自2026年3月1日生效。

適用範圍：符合 CNS 16047 或經濟部能源署認可的 LED 平板燈具。

能源效率要求：依 CNS 16047 測試，符合節能標章能源效率基準。

通訊功能驗證：須符合 CNS 16014，並提供 CNS 17025 認證實驗室測試報告，驗證電源控制、亮度與色溫調節功能。

申請文件：提交 CNS 16047/16014 測試報告及相關安規文件。

標示規範：產品或包裝須標示 製造商/代理商資訊，並清楚列出 功率、光通量、演色性、色溫、發光效率、閃爍指數、待機功率 等規格，具通訊埠產品須特別標註。

詳情請參考此連結。

ENERGY ADMINISTRATION, MOEA Order is hereby given, for the promulgation of “Energy Efficiency Criteria and Labeling Method for Energy Label Qualified for LED Flat Panel Lamps With Standard Interconnection Protocol Communication Port”, promulgation shall become effective from 1st, March 2026.
Eligibility: Must meet CNS 16047 or Energy Administration approval.
Efficiency: Tested per CNS 16047, meeting required standards.
Communication: Requires CNS 16014 compliance & accredited lab report.
Application: Submit CNS 16047/16014 test reports & safety documents.
Labeling: Display key specs (power, efficiency, flicker, etc.) & “with communication port” if applicable.
For more details, please refer to this link.

 

 

其他 / 多主題產品 Others / Products with Multiple Subjects

澳洲 Australia

澳洲發佈網路安全 (智慧設備安全標準) 法規2025版

2024 年網路安全法案已成為澳洲的官方法律。作為該法律實施的一部分，澳洲內政部於 2025 年 3 月 4 日推出了 2025 年網路安全 (智慧設備安全標準) 規則，為消費級智慧設備設定了強制性網路安全要求。
該規則將於 2026 年 3 月 4 日生效，製造商和分銷商有一年的時間來確保合規性。製造商和分銷商必須遵守類似於 EN 303 645 的嚴格安全措施，包括：
• 禁止使用通用預設密碼;
• 實施漏洞報告機制;
• 定義安全更新的支持期。
要在澳洲銷售消費類 IoT 商品，企業必須提供合規聲明，確認符合這些安全標準。

該文件必須包括：商品類型和批次編碼; 製造商和代表詳細資訊;合規聲明;支援短期資訊; 地點、日期和簽名。

The Cybersecurity Act 2024 has become official Australian law. As part of the implementation of the law, on March 4, 2025, the Australian Department of Home Affairs introduced the Cyber Security (Security Standards for Smart Devices) Rules 2025, which set mandatory cybersecurity requirements for consumer-grade smart devices.

The Rule will begin on March 4, 2026, giving manufacturers and distributors one year to ensure compliance. Manufacturers and distributors must comply with strict safety measures similar to EN 303 645, including:

• It is forbidden to use a universal default password.
• implement a vulnerability reporting mechanism.
• Define the support period for security updates.

To sell consumer IoT products in Australia, businesses must provide a declaration of compliance confirming compliance with these security standards. The document must include product type and batch identifier; Manufacturer and representative details; Declaration of Compliance; support period information; Location, date, and signature.

 

Chile智利

智利發佈電動往復鋸 (牽引鋸) 安全認證分析和/或測試認證協議 PE No. 6/09:2024

[法規草案] 2025 年 1 月 7 日，智利發佈安全認證分析和/或測試認證協議草案 PE No. 6/09:2024，並預計於2026年3月31日實施。該通報協議規定了電動往復鋸 (曲線鋸和馬刀鋸) 的安全認證程序，該鋸主要用於家庭或類似用途，配備單相電動機，電壓不超過交流電250V、直流75V (電池供電，附件K和L)，額定功率不超過3,700 W。

The Republic of Chile hereby advises that draft safety analysis and/or test certification protocol PE No. 6/09:2024 was published in the Official Journal on 7 January 2025 through Official Circular No. 263828 of 27 December 2024 of the Ministy of Energy/Electricity and Fuel Board.

The notified protocol establishes the safety certification procedure for electric reciprocating saws (jig and sabre saws), designed mainly for household or similar purposes, with a single-phase electric motor with a voltage not exceeding 250 V AC and not more than 75 V DC (battery operated, Annexes K and L), and rated power up to 3,700 W.

 

China中國

中國發佈國家標準《民用無人機系統運行識別規範》草案

[法規草案] 該文件規定了民用無人機系統運行識別的資訊內容、格式以及發送、接收和處理的功能和性能要求，並描述了相應的驗證方法。該檔適用於民用無人機系統、民用無人機系統廣播和網路運行識別專用接收設備以及用於民用無人機系統運行識別的網路鏈路的設計、生產、製造、試驗、檢驗、批准和運行。

On 17 February 2025, China released WTO document about National Standard  of  the  P.R.C.,  Specification  for  civil  unmanned  aircraft  system  operational identification.

This document specifies the information content and format for the operational identification of civil unmanned aircraft system, as well as the functional and performance requirements for sending, receiving and processing, and describes the corresponding verification methods.This  document  applies  to  the  design,  production,  manufacturing,  testing,  inspection, approval,  and  operation  of  civil  unmanned  aircraft  systems,  dedicated  receiving equipment  for  broadcasting  and  network  operational  identification  of  civil  unmanned aircraft  systems,  and  network  links  which  is  used  for  civil  unmanned  aircraft  system operational identification.

 

Turkey 土耳其

土耳其發布遠端商品銷售市場監督和檢查新法規

土耳其貿易部發布了《透過遠端通訊工具對市場供應產品進行市場監督和檢查的規定》。文件出現在 2024 年 10 月 30 日的官方公報上，編號為 32707。

該條例規定了供應商的許多新義務，並對仲介和服務提供者規定了額外的責任。如果經濟運營商向土耳其境內的個人或仲介銷售來自國外的產品，則他們也需要遵守該法規。

該法規自2025年4月1日起生效。

關於該條例的更多內容可參考此連結。

Turkey Issues New Regulation on Market Surveillance and Inspection for Distance Selling of Goods

The Ministry of Trade of Turkey issued the Regulation on Market Surveillance and Inspection of Products Supplied on the Market via Remote Communication Tools. The document appeared in the Official Gazette dated October 30, 2024 and numbered 32707.

The Regulation sets:

• the procedures and provisions regarding market supply conditions and sales advertisements of products that are sold via the Internet, telephone, and email
• the responsibilities of suppliers that place their products on the market via remote communication tools
• market surveillance procedures and principles

A product can be placed on the market via remote communication tools in the following cases:

• The product meets the relevant technical regulations or the General Product Safety Regulation
• The targeted end users are residents of Turkey

In case of selling over the Internet, the domain name must be registered in a geographical area where shipping to Turkey is possible.

The economic operator must include the following information in sales advertisements and prior to the end user purchasing the product:

• Name and registered trade name, postal and email address
• The name, registered trade name or trademark and full address of the manufacturer of the product resident in Turkey;
• If the manufacturer is not resident in Turkey, the importer’s name, registered trade name or trademark, postal and email address;
• Warning and safety information and signs of conformity in Turkish;
• Additional identification information of the product.

The Regulation introduces many new obligations for suppliers and set additional responsibilities on intermediary service providers and performance service providers.

If economic operators sell or mediate the sale of products from abroad to persons in Turkey then they also require to comply with the Regulation.

The Regulation becomes effective from April 1, 2025

The Regulation itself you can find via this link (Turkish)

資訊 / 電信 ITE / Telecom

Argentina阿根廷

國家通訊管理局 (ENACOM) 根據第1188/2024號決議分配固定衛星服務的新頻段

國家通訊機構 (ENACOM) 於 2024 年 12 月 3 日發佈了第 1188/2024 號決議。

1. 將71-76 GHz頻段分配給主要類別的衛星固定業務 (空對地)，將81-86 GHz頻段分配給主要類別的衛星固定業務 (地對空)。
2. 規定在根據第1條分配給固定衛星業務的頻段內，業務保護和頻率共用將按照國際電信聯盟無線電通訊規則和建議書、CITEL建議書和其他適用於此事項的國家和國際規則的規定進行調整。

National Body of Communications (Ente Nacional de Comunicaciones (ENACOM)) published Resolution 1188/2024 on December 3, 2024.

1. To allocate the 71-76 GHz frequency band to the Fixed Satellite Service (space-to-Earth), with primary category and 81-86 GHz to the Fixed Satellite Service (Earth-to-space) with primary category.
2. Establish that, in the frequency bands allocated by means of Article 1 to the Fixed Satellite Service, the protection of services and frequency sharing will be adjusted in accordance with the provisions of the Radiocommunication Regulations and Recommendations of the ITU, Recommendations of CITEL and other national and international regulations applicable in this matter.

 

Brazil巴西

巴西ANATEL發佈第772號決議，關於頻段分配、目的地和分佈的計畫

第772號決議是ANATEL於1月22日發佈的新標準，廢除了舊的第759號決議。該決議於2025年2月3日生效。

該標準是巴西頻段分配、目的地和分佈的計畫，它定義了巴西每個頻段的應用和業務，類似於FCC 2.106。

第772號決議帶來了一些頻段的分配和使用的實施和變化，只有在第680號決議的技術規格表中定義的具有替代發射限值的受限輻射設備可用的無線電頻段中的一些頻段的變化。

然而，這些變化只影響部分頻段，並且絕大多數是很少使用的頻段，而沒有改變測試技術要求。因此，WWAN， WLAN，藍牙，Zigbee， LoRa和許多其他將不會受到影響。

Anatel New Resolution No. 772 is a new standard issued by ANATEL on January 22, revoking the old Resolution 759. It came into force on February 03rd, 2025.

This standard is the plan for the assignment, destination and distribution of frequency bands in Brazil, which defines the application and services intended for each frequency band in Brazil, analogous to FCC 2.106.

Resolution 772 brought implementations and changes in the allocation and use of some frequency bands, in addition to some changes in bands in the RADIO FREQUENCY BANDS USABLE FOR RESTRICTED RADIATION EQUIPMENT WITH ALTERNATIVE EMISSION LIMITS, defined in the technical specifications table of Resolution 680.

However, these changes only affect some bands, and the vast majority of which are little-used bands, without changing testing technical requirements. So, WWAN, WLAN, Bluetooth, Zigbee, LoRa, and many others will not be impacted.

 

Brazil巴西

ANATEL發佈新2015法案

近期ANATEL發佈了新的2105法案。該法規更新了WWAN設備的技術要求，修訂了法案3151 (ETA (WWAN) 設備的技術要求，除了行動電話) 和法案3152 (行動電話的技術要求)。本法將於2025年8月13日生效。

Recently, ANATEL published the new Act 2105. This regulation updates the technical requirements for WWAN devices, amending Acts 3151 (Technical Requirements ETA (WWAN) devices, except Mobiles) and 3152 (Technical Requirements for Mobile Phones). This Act will come into effect on August 13th, 2025.

With this update, new certification requirements have been incorporated for equipment employing emerging technologies aimed at the Internet of Things (IoT). Among the innovations introduced, notable highlights include compliance assessments for devices utilizing technologies such as 5G NB-NTN (Narrow Band Non-Terrestrial Networks), 5G RedCap (Reduced Capability), and 4G LTE Cat 1bis. In addition to incorporating these new technologies, Act No. 2105/2025 has also updated the normative references for the certification of mobile phones and ETAs, ensuring that laboratory testing complies with the latest versions of the standards established by 3GPP.

 

Egypt埃及

2025 年 1 月 1 日起須透過 NTRA 數位服務平台進行國際行動裝置識別碼 (IMEI) 註冊

埃及國家電信管理局 (NTRA) 要求從2025年1月1日起通過 NTRA 數位服務平台進行國際移動設備識別碼 (IMEI) 註冊。2025年1月18日，NTRA 向手機製造商和進口商發送了指示，以方便在數位服務平台上進行 IMEI 註冊。

The National Telecom Regulatory Authority (NTRA) of Egypt required International Mobile Equipment Identity (IMEI) registration through the NTRA Digital Service Platform starting January 1, 2025. On January 18, 2025, NTRA sent instructions to mobile phone manufacturers and importers to facilitate IMEI registration on the Digital Service Platform.

 

India印度

印度TEC 宣佈部分產品豁免提交測試報告

2025年1月1日，印度通信工程中心 (TEC) 發佈通知，宣佈以下產品在MTCTE規範下可豁免提交測試報告，豁免期限至2025年6月30日或另行通知為止。

• 行動無線中繼系統
• 行動網路中繼器
• 精密時序協定主設備
• VHF/UHF 無線電系統設備
• 無線電廣播接收器
• ADSLx
• VDSLx
• 光纖 (單模)
• 光纖 (纜線)
• HF 無線電系統
• GSO VSAT/GSO 使用者終端
• NGSO 終端/NGSO 集成閘道

The India Telecommunication Engineering Centre (TEC) published  Notification on generic exemption from submission of test reports for several groups of products listed below under MTCTE until 30 June 2025 or further notice:

• Mobile Radio Trunking System
• Repeater for Cellular Network
• Precision Timing Protocol Grand Master Equipment
• VHF UHF Radio System Equipment
• Radio Broadcast Receiver
• ADSLx
• VDSLx
• Optical Fiber (Single Mode)
• Optical Fiber Cable
• HF Radio System
• GSO VSAT/GSO User Terminal
• NGSO Terminal/NGSO Integrated Gateway

 

Indonesia印尼

印尼對自2025 年 6 月 2 日起對影音類產品實施強制SNI認證

印尼工業部頒布了新法規，根據工業部長關於強制實施印尼音訊視頻國家標準的 2024 年第 75 號法規，要求印尼音視頻設備國家標準 – SNI IEC-62368-1：2014 取代之前的法規。
第 75/2024 號條例於 2025 年 6 月 2 日生效。

The Indonesian Ministry of Industry has issued the new regulation which mandates the Indonesian National Standard for audio video device – SNI IEC-62368-1:2014, under the Minister of Industry Regulation No. 75 of 2024 on the Mandatory Implementation of Indonesia National Standard for Audio Video (“Regulation 75/2024”) to replace the previous regulation.
Regulation 75/2024 applies effectively on 2 June 2025.

 

Indonesia印尼

SDPPI 已經更名為DJID，將影響證書格式

Kementerian Komunikasi dan Informatika  (KOMINFO) 現更名為Kementerian Komunikasi Digital (KOMDIGI)； SDPPI更名為DJID (dirktorat Jenderal infrastructure Digital)。新標誌將用於所有官方文件和通訊中。從2025年1月20日起，將頒發帶有新KOMDIGI標誌的證書。新的證書編號格式將與證書上的QR碼一起實施，現在將包含新的品牌。

Kementerian Komunikasi dan Informatika  (KOMINFO) is now Kementerian Komunikasi dan Digital  (KOMDIGI) and SDPPI changing to DJID (Direktorat Jenderal Infrastruktur Digital). The new logo will be used in all the official documents and communications.

 

Indonesia印尼

印尼發佈 2025 年第 2 號通訊與數位部長 DJID 條例，許可RLAN/SRD頻段

印尼通信和數位部 (KOMDIGI) 發佈了2025年第2號部長法令，根據RLAN(5925-6425MHz)/SRD 設備的類別許可證和技術標準規範無線電頻譜。該條例於2025年1月15日正式實施。 此次更新旨在為在印尼按類別許可證運營的電信和無線電頻率設備提供更明確的技術和操作指南。

The Indonesian Ministry of Communication and Digital Affairs (KOMDIGI) has issued Regulation No. 2 of 2025, revising the previous Ministerial Regulation No. 2 of 2023 regarding the use of radio frequency spectrum based on a class license. This update aims to provide clearer technical and operational guidelines for telecommunications and radio frequency devices that operate under class licenses in Indonesia.

 

Indonesia 印尼

印尼公佈最新的認可外國測試實驗室清單

印尼通訊與數位化(KOMDIGI)2025年2月發佈了KEPMEN KOMDIGI NO 13 TAHUN 2025，確認了最新的DJID (SDPPI)設備認證的認可外國測試實驗室清單。

該清單自2025年1月1日起生效，有效期至2026年12月31日。
Referring to circular letter No.B-618 /DJSDPPI.5/SP.04.06/10/2024 regarding Re-registration of SDPPI Recognized Foreign Testing Labs, DJID would like to inform you that The Decree of the Minister of Communications and Digital Affairs on the Recognition of Foreign Testing Labs No. 13 of 2025(KEPMEN KOMDIGI No. 13 Tahun 2025) was established on January 15, 2025.
The Decree of the Minister of Communications and Digital will be valid from January 1, 2025 until December 31, 2026.

 

Japan日本

MIC對於修改《終端設施規定》中規定的絕緣電阻規定已於2025年1月1日生效。

總務省 (MIC) 修改《終端設施規定》中規定的絕緣電阻規定，以符合現行國際標準 IEC62368，已於2025年1月1日生效。

此外，針對與電信線路設施 (網路) 互連使用的終端設備，對符合性標誌的終端設備的技術標準分類將從A至F六類重新組織為G、H、P和Q四類。

日文版修正案文本可在此處查閱。

Ministry of Internal Affairs and Communications (MIC) amended the insulation resistance provisions specified in the Regulations for Terminal Facilities to comply with the current international standard, IEC62368. The revisions entered in force on 1 January, 2025.

In addition, the classification of conformity-marked terminal equipment to the technical

standards will be reorganized from six categories, A through F, to four categories, G, H, P, and Q, regarding the terminal equipment used by interconnection with telecommunications line facilities (networks).

The texts of the amendments in Japanese are available here.

 

Malaysia馬來西亞

馬來西亞 SIRIM 對 IPv6 蜂窩設備的臨時批准不會延長

馬來西亞標準與工業研究所 (SIRIM) 於2025年2月10日宣佈，從2025年7月10日起，支持IPv6和LTE蜂窩設備的產品的新型批准申請和證書更新將強制要求提供IPv6報告。IPv6的本地測試實驗室現在是能滿足測試的，因此IPv6設備的臨時批准將於2025年7月10日結束，不會延期。

Malaysia SIRIM had announced that interim approval for IPv6 cellular equipment without a WiFi interface or IPv6 equipment over other mediums (e.g: fiber optic etc. except Ethernet LAN), currently in place, which ends on 10th July 2025, will not be extended. Full approval shall be granted after 10th July 2025, provided that applicants submit a complete IPv6 test report, including for non-Wi-Fi-enabled products.

Therefore, the renewal of the Certificate of Conformity (CoC) will not be permitted unless an IPv6 test report is submitted for SIRIM’s evaluation. Full approval will only be granted if IPv6 over cellular interfaces or other applicable mediums fully meets IPv6 requirements.

For Wi-Fi-enabled products, testing may be conducted at any IPv6 accredited laboratory.

Meaning that, previously those Cellular only product are accepted interim without IPV6 test report.

Now all those product must have IPV6 test report to apply type approval.

And renewal for previous accepted product will need to have IPV6 test report upon renewal.

 

Malaysia馬來西亞

馬來西亞發佈2025年最新電信設備公告摘錄

馬來西亞MCMC於2025年1月20日發佈最新電信設備公告摘錄CLASS ASSIGNMENT NO. 1 OF 2025。

Malaysian Communications and Multimedia Commission (MCMC) issued CLASS ASSIGNMENT NO. 1 OF 2025.

Class assignment confers rights on any person to use the frequency (ies) for a list of devices. The usage of devices under class assignment is subject to conditions provided in the class assignment issued under section 169 of CMA. No fee shall be payable for class assignment. A class assignment is valid until it is cancelled by MCMC.

Examples of Class Assignment:

• Walkie-Talkie (Family Radio System)
• Wireless LAN and Bluetooth
• Mobile Wireless Charger
• Remote Control

No application is required for Class Assignment. The devices must be certified by MCMC or its registered certifying agency.

 

Mexico墨西哥

墨西哥 IFT 發佈針對低功耗裝置的 IFT-016-2024條例

墨西哥聯邦電信協會 (IFETEL) 於2025年2月7日發佈IFT-016-2024條例，概述在30 MHz至3 GHz範圍內使用頻段的低功率無線電通信設備 (LPD) 的規格、限制和測試方法。

該法規將於2025年11月4日開始強制，屆時認證機構 (CBs) 和測試實驗室可以進行符合性評估，只要它們具有IFT或具有相應IFT授權的認可機構所需的認可。

The Instituto Federal de Telecomunicaciones (IFETEL) of Mexico published Disposición Técnica IFT-016-2024 on February 7, 2025. Disposición Técnica IFT-016-2024 outlines specifications, limits, and test methods on low-power radiocommunications devices (LPDs) that use frequency bands within the 30 MHz to 3 GHz range.

This regulation applies to various low-power devices, including:

• Generic low-power transmitters (Non-Specific Short Range Devices)
• Wireless microphones
• Hearing-aid devices
• Wireless alarm systems

Exceptions include frequency bands identified for emergency, safety, search or rescue communications; protected spectrum in the National Frequency Allocation Table (NFAT); and applications inconsistent with band use according to the NFAT. The scope does not include frequency hopping and digital modulation radio communications devices under IFT-008 (NOM-208) that operate in the 902-928 MHz, 2400-2483.5 MHz and 5725-5850 MHz frequency bands.

The Disposición Técnica will enter into effect 270 days after publication, on November 4, 2025. Certification Bodies (CBs) and Testing Labs may carry out conformity assessment starting November 4, 2025, as long as they have the accreditation needed by IFT or an Accreditation Body with corresponding IFT authorization. They may begin accreditation and authorization procedures starting February 8, 2025.

Certificates of Homologation (CoHs) that have been issued according to the Guidelines for granting Authorization Certificates for secondary use of frequency bands of the radioelectric spectrum will remain valid until they expire and will not be subject to certification monitoring compliance. Devices with a CoH under the new Disposición Técnica must follow the parameters outlined in IFT-016-2024. LPDs operating outside of the 30 MHz-3 GHz and receiving a Type B CoH must observe technical and operating parameters described in IFT-016-2024. Exceptional cases are applied to bands identified as protected spectrum for emergency, safety, search or rescue communications, and whose application is not consistent with use outlined in the NFAT.

 

Mexico墨西哥

墨西哥 IFT 發佈適用於 WLAN 裝置的 IFT-017-2023條例

墨西哥聯邦電信協會 (IFETEL) 於2025年2月10日發佈Disposición IFT-017-2023，該標準規定了在無許可頻段5150-5250 MHz、5250-5350 MHz、5470-5600 MHz、5650-5725 MHz、5725-5850 MHz和5925-6425 MHz使用無線局域網和/或使用數位調製技術的無線電通信設備的技術規範。

該條例將在2025年11月7日生效。一旦生效，針對數位調製設備和混合設備的數位調製部件的5725-5850 MHz頻段的規範和測試方法將在Disposición IFT-008-2015中廢止。在2025年11月7日之前已啟動批准程序的在以下任何或所有頻段 (5150-5250 MHz, 5250-5350 MHz, 5470-5600 MHz， 5650-5725 MHz和5925-6425 MHz) 運行的設備將根據B類或C類批准程序進行解決。認可機構在收到IFT的授權後，可於2025年2月11日開始授權合格評定機構的程序。

在2025年11月7日之前頒發的在以下任何或所有頻段 (5150-5250 MHz, 5250-5350 MHz, 5470-5600 MHz, 5650-5725 MHz， 5725-5850 MHz和5925-6425 MHz) 運行的產品的批准證書將繼續有效，直到其到期，並將接受審查和驗證程序。在2025年11月7日之前發佈的在5725-5850 MHz頻段運行的產品的符合性證書 (CoC) 將繼續有效，直到其失效日期，並且將受到合規性監控，但5725-5850 MHz頻段的數位調製設備和混合設備部分除外。

The Instituto Federal de Telecomunicaciones (IFETEL) of Mexico published Disposición Técnica IFT-017-2023 on February 10, 2025, which establishes technical specifications for devices that use WLAN and/or radiocommunication equipment using digital modulation technique operating in unlicensed frequency bands 5150-5250 MHz, 5250-5350 MHz, 5470-5600 MHz, 5650-5725 MHz, 5725-5850 MHz and 5925-6425 MHz.

Disposición Técnica IFT-017-2023 comes into effect 270 days after publication, on November 7, 2025. Once in effect, specifications and test methods for the 5725-5850 MHz band are repealed for digital modulation equipment and digital modulation parts of hybrid equipment in Disposición Técnica IFT-008-2015.

Equipment operating in any or all of the following frequency bands (5150-5250 MHz, 5250-5350 MHz, 5470-5600 MHz, 5650-5725 MHz, and 5925-6425 MHz) that have had approval procedures initiated prior to November 7, 2025, will be resolved according to Type B or Type C approval procedures.

Accreditation Bodies may begin procedures for their authorization of Conformity Assessment Bodies starting February 11, 2025, upon receiving authorization from IFT.

Prior approval of complementary products needed for EBP tests will be required after 365 days from Disposición Técnica IFT-017-2023’s entry into force.

Approval certificates issued prior to November 7, 2025 for products operating in any or all of the following bands (5150-5250 MHz, 5250-5350 MHz, 5470-5600 MHz, 5650-5725 MHz, 5725-5850 MHz and 5925-6425 MHz) will continue to be valid until their expiration date, and will be subject to review and verification procedures. Certificates of Conformity (CoCs) for products operating in the 5725-5850 MHz band that are issued prior to November 7, 2025, will continue to be valid until their expiration date, and will be subject to compliance monitoring with the exception of digital modulation equipment and hybrid equipment part of the 5725-5850 MHz band.

 

Morocco摩洛哥

摩洛哥ANRT宣佈新決定，包括標籤修改以及顯示SAR值的義務

摩洛哥ANRT於2025年1月20日公佈了一項新的核准決定，主要修改如下：

• 標籤修改:

對於標籤大小、字體和文本大小沒有具體的說明。標籤以清晰、易讀、不可磨滅的方式貼在設備上。如果由於設備的尺寸而無法進行此類操作，則可以將其貼在隨附的文件上，在其包裝上或通過電子標籤允許查看。

• 顯示SAR值的義務:

對於任何批准或授權設備，其發射功率大於20 mW, 且使用時距離用戶最多20釐米時, 必須在設備或隨附文件 (用戶說明、用戶手冊等) 或其包裝或要顯示的電子標籤內容 (如存在) 上以清晰易讀的方式標明比吸收率 (SAR) 的資訊，作為主要技術特徵。這項義務從2025年5月1日起生效。

Morocco ANRT announced a new decision, including new label design and the obligation to show SAR information.

• New Label design:

There are no specific instructions for label size, font and text size. The label is affixed to the device in a clear, legible and indelible manner. If this is not possible due to the size of the device, it may be affixed to the accompanying documentation, on its packaging or through an electronic label allowing viewing.

• Obligation to show SAR information:

For any approved or approved equipment, whose transmission power exceeds 20 and which is designed to be used at a distance not exceeding 20 from the user, the information relating to the Specific Absorption Rate (SAR) must be indicated as a main technical characteristic and in a legible and clear manner on the equipment itself or on the accompanying documents (brochure or user manual, etc.) or on the packaging or in the content of the electronic label that enables this information to be displayed (if such a label is present). This obligation also applies to any market offer, advertising or sale via the Internet of this equipment.

This commitment will come into effect as of May 1, 2025.

 

South Korea韓國

韓國發佈《簡易無線電台、太空站、地球站、無線電波探測及其他無線電設備用無線電設備技術標準》修正案草案

[法規草案] 本草案規定了在11GHz至14GHz頻段內運作在1100公里至1300公里高度之間的低軌道衛星通訊地球站無線電設備的技術要求。它是為了低軌道衛星通訊服務無線電波的安全使用以及保護人類的健康或安全。

South Korea released draft amendment of “Technical standards for radio equipment for simple radio stations, space stations, earth stations, radio wave detection and other radio equipment”.

This draft specifies technical requirements for radio equipment of earth stations communicating with low-orbit satellites operating at altitudes between 1,100 km and 1,300 km in the 11 GHz to 14 GHz frequency bands. It is for safe use of radio waves for low-orbit satellite communication services and for protection of human health or safety.

 

South Korea韓國

關於修訂7項電器安全標準的行政通知(草案)

[法規草案] 韓國技術和標準局(KATS)於2025年2月10日發佈草案，以修訂電氣用品安全標準，並就修訂目的及主要內容，事先聽取業界及公眾意見。

1. 修改原因: 更新安全標準以符合國際電氣用品安全管理公約 (WTO/TBT、IECEE)
2. 目標電器安全標準 (請見下圖)
3. 草案蒐集截止至2025年4月10日

The Korean Agency for Technology and Standards (KATS) published a draft on February 10, 2025, to amend electrical safety standards in accordance with Article 5, Paragraph 3; Article 15, Paragraph 4; and Article 23, Paragraph 4 of the Electrical Appliances Safety Control Act. This revision aims to gather opinions from industry stakeholders and the public regarding the purpose and key contents of the amendments. In compliance with Article 46 of the Administrative Procedures Act, the notice is issued as follows:

1. Reason for Amendment: Updating safety standards to align with international electrical safety management conventions (WTO/TBT, IECEE).
2. Targeted Electrical Safety Standards: (see above image)
3. Deadline for Draft Feedback: Until April 10, 2025.

 

South Korea韓國

韓國延後實施行動和智慧型裝置的充電和資料傳輸方法的USB Type-C技術法規

2024年11月8日韓國科學與資訊通訊技術部 (MSIT) 公佈關於廣播和通訊設備 (包括行動和智慧型裝置) 充電和資料傳輸方法的USB Type-C技術法規，共有13項裝置在連接充電或同時充電和資料傳輸時必須配備 USB Type-C並符合RRA SDoC認可。原定前12項產品預計2025年2月14日起實施，第13項筆電預計2026年4月起實施，但該規定將延期執行，待韓國無線電研究所RRA進一步通知。

On November 8, 2024, the Ministry of Science and ICT (MSIT) of South Korea announced USB Type-C technical regulations for charging and data transmission methods applicable to broadcasting and communication equipment, including mobile and smart devices.

The regulations require the above 13 types of devices to be equipped with USB Type-C ports and comply with the RRA SDoC approval when connecting for charging or simultaneous charging and data transmission. Initially, the first 12 product categories were scheduled for implementation starting February 14, 2025, while the 13th category—laptops—was set to be enforced from April 2026. However, the implementation has been postponed, pending further notice from the National Radio Research Agency (RRA) of South Korea.

1.Mobile phones

2. Tablets
3. Digital cameras
4. Headphones
5. Headsets
6. Portable gaming consoles
7. Portable speakers
8. E-readers
9. Keyboards
10. Mice
11. Portable navigation devices
12. Earphones
13. Laptops (to be implemented in April 2026)

 

Vietnam越南

越南發佈有關 ICT 產品認證和聲明的新法規草案。

[法規草案] 新法規一旦獲得批准並實施，它將取代現行的 30/2011/TT-BTTTT 號通函。

該通告草案將於 2025 年 2 月 25 日前接受公眾意見徵詢。

Vietnam publishes new draft Regulation on certification and declaration for ICT products. Once it’s approved and implemented, it will replace current Circular No. 30/2011/TT-BTTTT

The draft circular recieves public comments till Feb-25 of 2025.

 

India印度

TEC正式公佈電信設備的強制性檢測和認證(MTCTE)第VI期的生效日期及其涵蓋的產品清單

2025年3月4日，印度電信工程中心 (TEC) 正式公佈電信設備的強制性檢測和認證(MTCTE)第VI期的生效日期及其涵蓋的產品清單。這一新階段將從2025年8月24日起強制實施。在此日期之後，未經MTCTE批准，OEM製造商將不允許進口，銷售或分銷這類電信設備。

The Telecom Engineering Centre (TEC) has officially announced the effective date and list of products covered under MTCTE Phase VI.

This new phase will become mandatory from August 24, 2025. After this date, OEMs will not be allowed to import, sell, or distribute telecom equipment without MTCTE approval.

第6階段強制產品清單

Products Covered Under MTCTE Phase VI

S.No.	Telecom Equipment 產品名稱	Essential Requirements (ER) No & Name 標準要求(ER)號碼及英文名稱
1	Cellular Customer Premises Equipment 行動用戶終端設備	TEC40012408 (Cellular Customer Premises Equipment)
2	Fixed Wireless Phone with VOICE and DATA Facility 具語音與數據功能的固定無線電話‌	TEC10012409 (Fixed Wireless Phones)
3	Fixed Wireless Phone with Voice Facility only 僅具語音功能的固定無線電話	TEC10012409 (Fixed Wireless Phones)
4	Storage Area Network (SAN) Switch 儲存區域網路 (SAN) 交換器	TEC37942410 (LAN Switch)
5	Fabric Interconnect Switch 光纖互連交換器	TEC37942410 (LAN Switch)
6	Network Security Management Equipment 網路安全管理設備	TEC34732410 (IP Security Equipment)
7	Network Security Analytics Equipment – Managed 網路安全分析設備 – 代管式	TEC34732410 (IP Security Equipment)
8	Network Security Analytics Equipment – Unmanaged 網路安全分析設備 -非代管式	TEC34732410 (IP Security Equipment)
9	Content Security Equipment 內容安全設備	TEC34732410 (IP Security Equipment)
10	DDoS Protection Equipment 阻斷服務攻擊 (DDoS) 防護設備	TEC34732410 (IP Security Equipment)
11	Malware Analysis Equipment 惡意軟體分析設備	TEC34732410 (IP Security Equipment)
12	Web Application Firewall 網站應用程式防火牆	TEC34732410 (IP Security Equipment)
13	NGSO User Terminals 非地球同步軌道 (NGSO) 用戶終端機	TEC57282501 (Satellite Communication Equipment)
14	NGSO Integrated Gateway 非地球同步軌道 (NGSO) 整合閘道器	TEC57282501 (Satellite Communication Equipment)

 

 

 

 

電池 Batteries

Taiwan 台灣

2026年7月1日起實施「應施檢驗放置型鋰儲能裝置商品之相關檢驗規定」

鑑於儲能系統中使用的鋰離子電池存在熱失控風險，BSMI 已將固定式鋰電池儲能設備納入強制性檢驗範圍，以保障使用者安全。表列商品檢驗方式採型式認可逐批檢驗或驗證登錄雙軌並行，詳情請參考此連結。

To achieve net-zero carbon emissions by 2050, it is expected that renewable energy power generation equipment and energy storage systems will gradually enter households. Due to the risks associated with thermal runaway in lithium-ion batteries used in energy storage systems, the BSMI add stationary lithium battery storage appliances into the mandatory inspection scope. Two alternative conformity assessment procedures are made available for the choice of applicants, i.e. Registration of Product Certification (RPC) or Type-Approved Batch Inspection (TABI).
For details, please see this link.

 

 

家用電器 House Appliances

Australia澳洲

澳洲和紐西蘭標準局發佈AS/NZS 2040.1:2021 電動洗衣機性能標準的修正案

[法規草案] 2024 年 12 月 20 日，澳洲和紐西蘭標準局編制了標準 AS/NZS 2040.1:2021 的修正案 – DR AS/NZS 2040.1:2021 Amd 1:2024

本標準規定了用於確定立法範圍內的家用和類似用途的電動洗衣機性能特徵的測試程式和最低性能標準。意見徵詢截止日期為 2025 年 2 月 21 日。

On December 20, 2024, the Standards Australia & New Zealand prepared draft amendment 1 to Standard AS/NZS 2040.1:2021. — DR AS/NZS 2040.1:2021 Amd 1:2024

This Standard specifies test procedures and minimum performance criteria for determining the performance characteristics of electric clothes washing machines intended for household and similar use that are within the scope of the relevant legislation.
Closing date for comments is on February 21, 2025.

 

Brazil巴西

INMETRO對冰箱和類似器具的綜合法規進行修訂

2024 年 12 月 11 日，國家計量、品質和技術局 (INMETRO) 發佈了 2024 年 12 月 10 日 Portaria 736 號法規，對 2021 年 8 月 2 日 Portaria 332 號法規 (冰箱和類似器具的綜合法規) 進行了修訂，對 Portaria 332/2021 號法規的修改於同日生效。

該法令修訂了冰箱及類似設備的符合性評估要求，主要涉及能效標籤、技術規範和測試要求等方面的更新。
On December 11, 2024, the National Institute of Metrology, Quality and Technology (INMETRO) issued Portaria 736 of December 10, 2024, amending Portaria 332 of August 2, 2021, the consolidated regulation for refrigerators and similar appliances. The changes to Portaria 332/2021 enter into force on the same day.

The amendment revises the conformity assessment requirements for refrigerators and similar equipment, mainly involving updates to energy efficiency labels, technical specifications and testing requirements.

 

India印度

印度發布《冷凍設備 (品質控制) 修正案，2025年》

2025年1月16日 DPIIT公布《Refrigerating Appliances (Quality Control) Amendment Order, 2025》，修訂內容如下:

經認證ISI mark的製造商進口零件豁免：

• 獲得認證的製造商 (或申請BIS認證的製造商) 可以進口零件用於出口。
• 需要自我聲明和承諾，以確保這些組件不會在國內市場上銷售。
• 必須保留記錄以供審計。

用於研究與開發 (R&D) 目的的豁免：

• 製造商每年最多可進口200台研發。
• 這些設備不得進行商業銷售，且使用後必須報廢。
• 必須保留逐年紀錄。

The Ministry of Commerce and Industry has introduced the 《Refrigerating Appliances (Quality Control) Amendment Order, 2025》, which came into effect on January 16, 2025, upon its publication in the Official Gazette

Key Requirement:

All refrigerating appliances must comply with their respective Indian Standards and bear the Standard Mark (BIS Certification) under Scheme-I of Schedule II of the BIS (Conformity Assessment) Regulations, 2018.

Key Amendments in the Order:

Exemption for Imported Components by Certified Manufacturers:

• Certified manufacturers (or those applying for BIS certification) can import components for export purposes.
• A self-declaration and undertaking are required, to ensure these components are not sold in the domestic market.
• Records must be maintained for audits.

Exemption for Research & Development (R&D) Purposes:

• Manufacturers can import up to 200 units annually for R&D.
• These units must not be sold commercially and must be scrapped after use.
• Year-wise records must be maintained.

These changes aim to support exports and innovation while ensuring compliance.

 

Indonesia印尼

印尼發佈2025年第7號工業部長法令，家用電器產品SNI認證迎來新規則

工業部發佈了關於強制實施家用電子產品印尼國家標準 (SNI) 認證的新法規 (工業部法規2025年第7號)。該法規取代了空調、洗衣機、冰箱、水泵、電熨斗、廚房機械和加熱液體的 SNI 法規。

新法規將於2025年7月24日生效，並於2026年7月24日實施。

Ministry of Industry has issued new regulation (Ministry of Industry regulation No. 7 year 2025) concerning the Mandatory Implementation of the Indonesian National Standard (SNI) Certification for Household Electronics. This regulation is replacement of the SNI Regulation of Air Conditioning, Washing Machine, Refrigerator, Water Pump, Electric Iron, Kitchen Machine, and Heating Liquid.

The new regulation will come into force on July 24th 2025 and will be implemented on July 24th 2026.

Highlights:

1. New application refers to new regulation (Ministry of Industry regulation No. 7 year 2025)

The new application following this new regulation can be started on July 24th 2025 and/or after we received appointment from the Ministry. Currently, the Ministry has not announced the estimation of the appointment release date.

2. On going application

All projects that currently still on-going (new certification, additional family, additional model, and surveillance) which refer to the old regulation, must be completed before the new appointment released. If it is not completed, the certification process needs to be restarted by referring to the new regulation.

3. Surveillance Schedule and Completion Target
4. a) The surveillance scheduling will follow provisions in SNI old regulation and/or LSPro scheme, which allows ±3 months from surveillance schedule that stated in the certificate.
5. b) Considering the estimated project completion and issuance of Certification Body/LSPro and Lab appointments, we will limit audit and market sampling activities until March 2025. Surveillance schedule that can be conducted until March 2025 (following the provisions in point 3a) will be contacted separately by our team for further arrangement.
6. Certificate Validity
7. a) Certificates that have completed surveillance in 2025 (and previous years) before the appointment for Certification Body/LSPro and Laboratory are issued, will remain valid until the next surveillance.
8. b) Certificates which surveillance scheduled after the appointment for Certification Body/LSPro and Laboratory are issued, cannot conduct surveillance and will be terminated based on the maximum tolerance for surveillance.

 

Saudi Arabia沙烏地阿拉伯

SASO發佈家用冰箱和洗衣機的能效、測試及標籤要求的2025版標準草案

[法規草案] 沙烏地阿拉伯標準與品質組織 (SASO) 發佈了針對家用冰箱和洗衣機的能源性能、測試及標籤要求的新版草案標準Draft SASO 2892:2025和Draft SASO 2885:2025。

公眾諮詢期為發佈後60天。建議的通過和生效日期是在官方憲報公佈之日起2年後。

The Saudi Standards and Quality Organization (SASO) has published new draft standards for energy performance, testing and labeling requirements for household refrigerators and washing machines, Draft SASO 2892:2025 and Draft SASO 2885:2025.

The final date for comments is 60 days from the date of notification. The proposed adoption and entry into force date is 2 years after the date of publication in the official gazette.

 

South Korea 韓國

韓國能源廳發佈 [能源效率等級制度] 各能效管理設備適用標準生效日期資訊

2025年1月2日，韓國能源廳發佈了一份關於能源效率法規管控範圍內的各類產品的能效標準實施日期的通知。製造商在創建能效標籤時必須參考這份通知中對應的產品標準實施日期。

以電冰箱為例：能效標籤上的0000.00.00需要更改為2021.10.01

On 02 January 2025, Korea Energy Agency published Efficiency Rating System Information on the effective date of application standards for each item of efficiency management equipment. Manufacturers must refer to the implementation date of the product standards in this notice when creating energy efficiency labels.

Taking refrigerators as an example, 0000.00.00 must be changed to 2021.10.01 on the energy efficiency labels.

 

Taiwan 台灣

「電冰箱容許耗用能源基準與能源效率分級標示事項、方法及檢查方式」 修正 草案

2025年2月10日，台湾BSMI向WTO提交了「電冰箱容許耗用能源基準與能源效率分級標示事項、方法及檢查方式」 修正草案。

公众咨询期截至2025年4月11日，拟议生效日期: 2027年1月1日。

Taiwan released draft announcement for amendment to Requirements on Minimum Energy Performance Standard and Energy Efficiency Rating Labelling and Inspection for Refrigerators

Proposed date of adoption: To be determined

Proposed date of entry into force: 1 January 2027

 

UAE 阿拉伯聯合大公國

阿拉伯聯合大公國發佈電熱水器能源效率標籤標準UAE.S 5010-4草案

[法規草案] 該草案標準規定了儲水式電熱水器和即熱式電熱水器的能源效率標準和測試要求。

該標準適用於功率小於或等於70千瓦的熱水器，以及容量不超過2000公升的各類熱水器產品。

UAE released draft standard – Labeling – Energy  Efficiency  Label  for  Electrical  Appliances UAE.S 5010-4 Part  4 – Electrical  water  heater.

This Standard specifies the Energy Performance Standard and testing requirements of electric storage water heaters and Instantaneous electric water heaters.

It shall apply to water heaters with power under or equal to 70 kW and to products with a capacity up to 2,000 liters for all types of water heaters

 

India印度

印度發布《空調及其相關零件、全封閉壓縮機和溫度感測控制器 (品質控制) 修正令，2025 年》

2025年2月11日，DPIIT 更新2019年版QCO 至《the Air Conditioner and its related Parts, Hermetic Compressor and Temperature Sensing Controls (Quality Control) Amendment Order, 2025》。

針對空調和冷凍設備製造商，自2025年版修正案生效日一年之內，容量超過7000瓦 (2噸) 的密閉式壓縮機延長一年豁免直至2026年2月11日後再納入。

On 11 February 2025, DPIIT updated the 2019 version QCO to 《the Air Conditioner and its related Parts, Hermetic Compressor and Temperature Sensing Controls (Quality Control) Amendment Order, 2025》. It shall be noted that nothing in this order shall apply to Hermetic Compressors of more than 7000 W (2TR) capacity for one year from the date of commencement of the Air Conditioner and its related Parts, Hermetic Compressor and Temperature Sensing Controls (Quality Control) Amendment Order, 2025 to the manufacturers of Air conditioning and Refrigeration equipment and related parts.

 

 

燈具 / LED Luminaiaries/LED

Australia澳洲

GEMS《溫室效應及能源最低標準 (一般照明用白熾燈) 決議2024》

GEMS於2024年12月23日發佈《溫室效應及能源最低標準 (一般照明用白熾燈) 決議2024》。

• 提高最低能源性能標準
• 改變可註冊模型的範圍
• 列出了不符合附表 1 中新要求的註冊類型清單
• 允許在 2025 年 10 月 4 日之前已進口或在澳洲生產的現有庫存在 2030 年 10 月 3 日之前供應給市場

除了 2024 年決議附表 1 所列的型號，供應商無需立即採取行動，可繼續銷售根據 2016 年決議註冊的現有白熾燈型號。新的要求僅在新的白熾燈型號需要註冊，或現有白熾燈型號註冊到期且需要註冊才能銷售時才會生效。

GEMS released the 《Greenhouse and Energy Minimum Standards (Incandescent Lamps for General Lighting Services) Determination 2024 》on December 23, 2024. From October 4, 2025, tungsten filament, carbon filament, and halogen incandescent bulbs that are in the scope of the regulations must meet and register under this new determination.

This 2024 determination:

Increases Minimum Energy Performance Standards.

Changes the scope of models that can be registered.

Includes a list of registered models that will not meet the new requirements under Schedule 1. These model registrations will expire on October 3, 2025, and they will no longer be approved for registration in Australia.

Sets out grandfathering arrangements, allowing existing stock already imported or manufactured in Australia prior to October 4, 2025, to be supplied to the market until 3 October 2030, provided they meet the grandfathering provisions.

No immediate action is required by suppliers to continue selling existing incandescent models registered against the 2016 determination – except for those listed in Schedule 1 of the 2024 determination. The new requirements only take effect when a new incandescent model needs to be registered, or when an existing incandescent model’s registration expires and it needs to be registered for sale.

Suppliers with a registration that is about to expire or are considering registering new models between October 4, 2024, and October 3, 2025, need to consider:

Whether they register the models under the 2024 or 2016 determination (subject to eligibility), or

when to discontinue models, if the model cannot be supplied after October 3, 2025.

 

Egypt埃及

埃及發佈標準 ES: 7825「燈具 – 一般要求和測試」草案

[法規草案] 埃及標準 ES 7825 的草案規定了燈具的一般要求，包括電源電壓高達 1000V 的電光源。

這些聲明可能要求，對於此類商品，先前的標準可以繼續適用於生產，直到規定的日期之後，新標準應適用。
另外值得一提的是，該標準草案在技術上與 IEC 60598-1/2020 相同。

This draft of Egyptian standard ES 7825 specifies general requirements for luminaires, incorporating electric light sources for operation from supply voltages up to 1000 V.  The requirements and related tests of  this document  cover classification, marking, mechanical,construction, electrical construction and photobiological safety.

The statements may require that for such products, the previous standard may continue to apply to production until a defined date after which the new standard shall apply.

Worth mentioning is that this draft standard is technically identical with IEC 60598-1/2020

 

 

能源效率要求 Energy Efficiency Requirements

Malaysia馬來西亞

馬來西亞頒布EECA節能新規，並於2025年1月1日實施

2024 年能源效率與保護法案 (EECA) 頒布，旨在規範馬來西亞的能源高效消耗和保護。

該新法案規定，用能產品的製造商和進口商必須向能源委員會註冊。涉及的產品必須滿足基本能源性能要求，加貼能源效率等級標籤，並支援在市場上使用節能產品。

The Energy Efficiency and Conservation Act (EECA) 2024 was enacted to regulate the efficient consumption and conservation of energy in Malaysia.

This new act has specified that manufacturers and importers of energy-using products must register with the Energy Commission. The products involved must meet basic requirements for energy performance, place an energy efficiency rating label, and support the use of energy-saving products in the market.

 

 

其他 / 多主題產品 Others / Products with Multiple Subjects

Australia澳洲

澳洲/紐西蘭官方常委會 (SCO) 發佈了一份關於含有插腳的插拔電源、電池充電器和類似設備的資訊公告。

該公告目的是防止對部分設備外殼配備美式或日式以及歐式插頭插腳的設備進行認證。

SCO指出，相關的國家標準 AS/NZS 3112 “其批准和測試規範–插頭和插座–插座 “將進行修訂，以明確有關設備中使用的可拆卸插頭部分的要求。
所有相關產品設備的製造商和供應商都應關注該公告以及澳大利亞和紐西蘭即將更新的要求。

The Standing Committee of Officials (SCO) issued an information bulletin regarding plug-pack type power supplies, battery chargers, and similar equipment with integral pins in Australia/New Zealand.
The aim of the bulletin is to prevent certification of devices equipped with integral plug pins of US or Japanese type, as well as European type plug pins that are form part of the device cover.
The SCO notes that the national standard AS/NZS 3112 “Approval and Test Specification – Plugs and Socket-Outlets” is going to be amended to clarify the requirement regarding detachable plug portions used in equipment.
All manufacturers and suppliers of power supplies, battery chargers, and similar equipment with integral pins should pay attention to the bulletin and the upcoming changes in Australia and New Zealand.

 

India印度

印度發布《手電筒 (品質控制) 命令，2025年》

2025年1月21日，DPIIT發布了正式的《手電筒 (品質控制) 命令，2025年》，計畫於2025年7月21日起實施。該產品屬於 ISI 標誌認證範圍。

On January 21, 2025, DPIIT released the official 《Flashlight (Quality Control) Order, 2025》, which will be in force after 6 months from the date of publication of QCO (= 2025/07/21). It’s under ISI mark approval.

 

Mexico墨西哥

墨西哥發佈交流感應電動機標準草案

[法規草案] 墨西哥發佈PROY-NOM-016-ENER-2024 標準草案, 適用於三相鼠籠非同步交流感應電動機，連續工作，使用空氣冷卻，可以水準或垂直安裝，具有單一轉速頻率，開環或閉環控制系統，功率範圍從0.746千瓦到373千瓦，可配置2、4、6或8極，至少標明的額定電壓高達 600V， 且在墨西哥境內進口、製造或銷售。

Mexico published draft Mexican Official Standard PROY-NOM-016-ENER-2024. This draft Mexican Official Standard establishes the minimum energy efficiency values, test method, marking requirements and conformity assessment procedure.

It applies to electric continuous duty, air-cooled, horizontally or vertically mounted, single rotational frequency (rotational speed of the motor shaft or axis), open- or closed-loop, three-phase squirrel-cage asynchronous AC induction motors with a rated output of 0.746 kW to 373 kW, 2, 4, 6 or 8 poles and at least a marked rated voltage of up to 600 V, which are imported, manufactured or marketed within the United Mexican States.

The following are excluded from the scope of this draft Mexican Official Standard: Electric motors that require auxiliary or additional cooling equipment.

 

Taiwan 台灣

2026年7月1日起實施「應施檢驗電動車充電設備商品之相關檢驗規定」

為了確保電動車充電設備的安全並保障消費者權益，BSMI 將目前屬於自願性產品認證 (VPC) 範疇的電動車充電設備（功率 ≤ 30kW）納入強制性檢驗的範圍內。BSMI 提供兩種合格評定程序，供申請人選擇：產品認證註冊 (RPC) 或 型式認可批次檢驗 (TABI)。

詳情請參考此連結。

Electric Vehicle Charging Equipment is becoming popular in household and indoor parking environments.
To ensure the safety of Electric Vehicle Charging Equipment and protect consumer rights, the BSMI includes Electric Vehicle Charging Equipment (less than or equal to 30 kW), which is currently subject to Voluntary Product Certification (VPC) into the scope of mandatory inspection of the BSMI. Two alternative conformity assessment procedures are made available for the choice of applicants, i.e. Registration of Product Certification (RPC) or Type-Approved Batch Inspection (TABI).
For details, please refer to this link.

 

Taiwan 台灣

2026年7月1日起實施「應施檢驗電力轉換系統商品之相關檢驗規定」

為了實現 2050 年淨零碳排放的目標，預期再生能源發電設備和儲能系統將逐步安裝於室外場域，也將延伸至室內家庭與工廠環境。考量到電力轉換系統 (PCS) 是儲能系統的關鍵元件，為了確保消費者安全，BSMI 已將 PCS 納入強制性檢驗範圍。

表列商品檢驗方式採型式認可逐批檢驗或驗證登錄雙軌並行. 詳情請參考此連結 。

To achieve net-zero carbon emissions by 2050, it is expected that renewable energy power generation equipment and energy storage systems will gradually be installed not only at outdoor sites but also in indoor households and factories. Considering that the Power Conversion System (PCS) is a critical component of energy storage systems, the BSMI includes PCS in the mandatory inspection scope to ensure consumer safety. Two

alternative conformity assessment procedures are made available for the choice of applicants, i.e. Registration of Product Certification (RPC) or Type-Approved Batch Inspection (TABI). For details, please see the link.