德國萊因TÜV認證 TÜV Rheinland Accreditation

Kenya 肯亞

德國萊因TÜV集團獲肯亞標準局 (KEBS) 授權，可為肯亞市場簽發合格證書 (CoC)

德國萊因TÜV集團已獲得肯亞標準局 (KEBS) 授權，可為肯亞市場簽發合格證書 (CoC)。所有進口至肯亞的貨物，除屬於豁免清單、限制清單或禁止清單外，均須在裝運前在出口國進行強制性認證。如有任何關於肯亞合格證書要求的問題，請隨時聯繫德國萊因TÜV集團。

TÜV Rheinland has been authorized by Kenya Bureau of Standards (KEBS) to issue Certificates of Conformity (CoCs) for the Kenyan market for a period of three years.
All imported goods destined to Kenya shall undergo mandatory certification in the country of export prior to shipment, unless they fall under any exempted list, restricted, or prohibited list.
Sould you have any quesitons to Kenya CoC requirement, please do not hesitate to contact TÜV Rheinland Group.

資訊 / 電信 ITE / Telecom

Algeria 阿爾及利亞

阿爾及利亞郵政和電子通信監管局 (ARPCE) 於2026年2月22日頒佈了第26-97號法令，對型式批准程式進行了更新。主要變更包括：
• 證書的有效期由3年變成5年
• 推出新的線上申請提交平台
提交申請和寄送樣品仍需通過一家阿爾及利亞當地公司辦理。

The Autorité de Régulation de la Poste et des Communications Électroniques (ARPCE) in Algeria issued Decree No. 26-97 on February 22, 2026, which updates Type Approval procedures. The main changes include:
• Certificate validity has been extended from 3 years to 5 years.
• The launch of a new online platform for submitting applications
A local Algerian company is still required for application submission and delivery of samples.

Argentina 阿根廷

阿根廷發佈對ENACOM認證框架的更新

2026年2月26日，阿根廷國家通訊管理局 (ENACOM) 發佈第57/2026號決議，撤銷了先前的主要決議729/1980，旨在建立一套全新的審批體系，以簡化和現代化阿根廷的電信設備認證流程。
本次更新的關鍵點如下：
• 新版RAMATEL法規框架將於2026年9月1日生效。
在該日期之前，現行ENACOM審批流程仍保持原有效力。
• 根據第586/2023號決議，獲批設備上市仍須強制標注RAMATEL監管標誌。
線上銷售時，賣方與電商平台均須在每件商品資訊中清晰展示對應的RAMATEL識別碼。
• 引入認證機構
設立本地協力廠商認證機構負責簽發符合性證書。
該機構須經阿根廷認證機構OAA依據IRAM ISO/IEC 17065標準正式認可。
• 檢測實驗室需獲得OAA認證
本地實驗室須經阿根廷認證機構OAA依據IRAM ISO/IEC 17025標準正式認可。
現有ENACOM認可實驗室享有2年過渡期以獲取認證。
• ENACOM證書現接受家族型號認證
新規框架允許將家族型號納入單份ENACOM認證證書。
• 電信設備商業化仍需強制獲取ENACOM認證
認證的電信設備現分為A類 (消費類產品) 和B類 (專業用途)
• ENACOM認證證書將不再設有效期
但A類設備須每兩年接受認證機構的監督審查。
B類設備無需接受監督流程
• 現有有效ENACOM證書的有效期將延長三年，至2029年2月26日。
此後必須根據新法規框架進行續期和重新認證。

On February 26th, 2026 the National Communications Entity (ENACOM) published Resolution 57/2026 to revoke the former main Resolution 729/1980, in order to establish a complete new approval scheme that aims to simplify and modernize Telecom Equipment Certification in Argentina.
The keypoints for these updates are as follows:
• The new RAMATEL regulation framework becomes effective on September 1st, 2026.
o Until that date, the current ENACOM approval process still remains in force as it is.
• RAMATEL regulatory marking remains mandatory for the commercialization of approved devices based on Res. 586/2023.
o For online sales, both sellers and marketplace platforms will now be required to clearly display the corresponding RAMATEL ID number in each product listing.
• Introduction of Certification Agencies
o The incorporation of local third-party Certification Bodies to be responsible for issuing Certificates of Conformity.
o They must be duly accredited by OAA (Argentinean Accreditation Body) under IRAM ISO/IEC 17065.
• Testing Laboratories now require OAA Accreditation
o Local labs will need to be duly accredited by the OAA (Argentinean Accreditation Body) under IRAM ISO/IEC 17025.
o Existing ENACOM recognized laboratories have a grace period of 2 years to seek accreditation.
• Family Approval is now accepted on ENACOM Certificates
o The new regulation frameworks accepts the concept of family models to be included on a single ENACOM Homologation Certificate
• ENACOM Approval remains mandatory for the commercialization of telecommunications devices
o Telecommunication devices subject to homologation are now classified as Class A (Consumer Products) and Class B (Professional Use)
• ENACOM Homologation Certificates will have no expiration date
o However, Class A devicesare subject to a surveillance process every 2 (two) years performed by Certification Agency.
o Class B devices will not require a surveillance process
• Existing ENACOM Certificates that are currently valid will have a their validity extended for 3 (three) additional years, until February 26th, 2029.
o After that date, they must be renewed and recertified in accordance with the new regulatory framework.

Bolivia 玻利維亞

玻利維亞再度更新需型式認證的電信產品清單

2026年3月，玻利維亞電信和運輸監管與審計局 (ATT) 再度更新需型式認證的電信產品清單，更新後的電信設備認證清單於 2026 年 3 月起生效。該清單此前於 2026 年 2 月 25 日更新。在更新清單發佈之日前提交的申請仍適用之前的清單要求。清單發佈後提交的申請則必須符合新清單的要求。

The Autoridad de Regulación y Fiscalización de Telecomunicaciones y Transportes (ATT) in Bolivia announced the updated list of telecommunications equipment subject to homologation will come into effect starting March 2026.
The list was updated on February 25, 2026. Applications submitted up until to the date of publication of the updated list will follow the previous list requirements. Applications submitted after the publication of the updated list must conform to the new list.

Chile 智利

智利SUBTEL就啟用600MHz頻段進行IMT通信公開徵求意見

[法規草案] 2026年3月10日，智利電信部 (SUBTEL) 就將600MHz頻段用於IMT通信業務公開徵求意見。意見徵集截至2026年4月9日。

On March 10, 2026, the Chilean Subsecretaria de Telecomunicaciones (SUBTEL) publicly solicited opinions on the use of the 600MHz frequency band for IMT communication services. The final date to give comments is April 9, 2026.

Colombia 哥倫比亞

哥倫比亞更新國家頻率分配表 (CNABF)

哥倫比亞國家頻譜管理局 (ANE) 於 2026 年發布了第 000028 號決議，更新了國家頻率分配表 (CNABF)，重點優化了 900 MHz 頻段。此次修訂允許該頻段支援更廣泛的無線電通訊服務，不再局限於先前預留用於國際行動通訊 (IMT) 的服務，從而改善偏遠和脆弱地區的通訊連接。

The National Spectrum Agency (ANE) of Colombia has issued Resolution 000028 of 2026 to update the National Frequency Allocation Table (CNABF), specifically targeting the optimization of the 900 MHz band. This amendment allows the band to support a wider range of radiocommunication services beyond its previous reservation for International Mobile Telecommunications (IMT) to improve connectivity in remote and vulnerable areas.

Egypt 埃及

埃及NTRA發布型號核准程序的最新資訊

埃及國家電信監管局 (NTRA) 發布了型號核准程序的最新資訊。所有型號核准方案 (輕型、中型和嚴格型方案) 的申請方式均已統一，本地和海外公司均需透過數位化型號核准入口網站進行申請。

The National Telecommunications Regulatory Authority (NTRA) of Egypt announced updates on Type Approval procedure. All Type Approval Schemes (Light, Intermediate and Tight Schemes), the method to apply for Type Approval is unified to be through digital Type Approval portal for both Local and overseas companies.

Hong Kong 香港

香港通訊事務管理局更新865-868 MHz及920-925 MHz頻段設備的性能規範

香港通訊事務管理局 (OFCA)於2026年3月18日發佈了以下性能規範:
• HKCA 1078 – 第2版 – 工作於920-925 MHz頻段的無線電設備性能規範
• HKCA 1049 – 第2版 – 工作於865-868 MHz和/或920-925 MHz頻段的射頻識別 (RFID) 設備性能規範

Hong Kong OFCA Updates Specifications for Devices in the 865-868 MHz and 920-925 MHz Bands.
The Office of the Communications Authority (OFCA) in Hong Kong published the following Performance Specifications on March 18, 2026:
•HKCA 1078 – Issue 2 – Performance Specification for Radio Equipment operating in the 920-925 MHz Band
•HKCA 1049 – Issue 2 – Performance Specification for Radio Frequency Identification (RFID) Equipment Operating in the 865-868 MHz and/or 920-925 MHz Bands

India 印度

印度將 IS 18112:2022 (電視機) 的實施日期延至 2026 年 7 月 26 日

印度將 IS 18112:2022《衛星廣播傳輸數位電視接收機—電視機規範》的實施日期延至 2026 年 7 月 26 日。

India postpones the implementation date for IS 18112:2022 Digital Television Receiver for Satellite Broadcast Transmission – Specification for Television Sets till Jul-26 of 2026.

India 印度

印度發布針對5G開放式無線存取網 (O-RAN) 的ITSAR要求)

印度發布了針對5G開放式無線存取網 (O-RAN) 的ITSAR (印度電信安全保障要求): RIC。實施日期尚未確定。

India publishes ITSAR (Indian Telecom Security Assurance Requirements) for Open Radio Access Network (O-RAN) of 5G: RIC. The implementation date is not determined yet.

India 印度

印度DoT發佈已獲證設備啟用 5925-6425 MHz 頻段的要求

印度電信部 (DoT) 此前於2026年1月20日發佈了將5925-6425MHz頻段用於免許可應用的公告。DoT注意到有部分產品此前在支援但禁用5925-6425MHz的前提下獲得了證書。DoT於2026年3月6日再次發佈通知，闡述了根據修訂後的監管框架啟用5925-6425MHz頻段的合規要求。對於能夠在5925-6425MHz 頻段運行但僅獲得2.4GHz和/或5GHz頻段證書的產品的利益相關方，應重新申請新證書來啟用5925-6425MHz頻段。這些必要步驟須在2026年4月5日之前完成。除非獲得新的證書授權，否則不得啟用、啟動或使用5925-6425 MHz頻段。

The Ministry of Telecommunications (DoT) of India previously issued an announcement on January 20, 2026, to use the 5925-6425MHz frequency band for license-exempt applications. The DoT noted that some products had previously received certificates which supported but disabled 5925-6425MHz. The DoT issued another notice on March 6, 2026, setting out the compliance requirements for enabling the 5925-6425MHz band under the revised regulatory framework. Stakeholders of products capable of operating in the 5925-6425MHz band but only obtaining certificates for the 2.4GHz and/or 5GHz bands should reapply for a new certificate to enable the 5925-6425MHz band. These necessary steps must be completed by April 5, 2026. The 5925-6425 MHz band may not be enabled, activated, or used unless a new certificate authorization is obtained.

Indonesia 印尼

印尼發佈關於行動通訊設備和平板電腦特定吸收率限制的草案

[法規草案] 通訊和數位部長公佈了關於行動通訊設備和平板電腦特定吸收率限制的通訊和數位技術部長令草案。該通訊和數位部長令草案將取代2024年第177號通訊和資訊部長令，該法令同樣涉及行動通訊設備和平板電腦的特定吸收率限制。

The Minister of Communication and Digital announced the Draft Decree of the Minister of Communication and Digital Technology concerning Specific Absorption Rate Limits on Mobile Telecommunications Devices and Tablet Computers. The Draft Decree of the Minister of Communication and Digital concerning Specific Absorption Rate Limits on Mobile Telecommunication Devices and Tablet Computers will replace the Decree of the Minister of Communication and Informatics Number 177 of 2024 concerning Specific Absorption Rate Limits on Mobile Telecommunication Devices and Tablet Computers.

Malaysia 馬來西亞

馬來西亞MCMC提醒UWB設備禁止使用3300MHz~3400MHz頻段

2026年2月11日，馬來西亞通信及多媒體委員會 (MCMC) 發佈公告：MCMC將取消《2025年第2版通信產品類別分配表》(Class Assignment No.2 of 2025) 中關於UWB設備附表中3300-3400MHz的頻譜分配。而該分配表中已規定3400-3700Mz頻段分配的有效期至2025年5月31日，因此自2026年4月1日起，UWB設備在馬來西亞不可使用3300-3700MHz頻段，可使用頻段為3700-10600MHz。

On February 11, 2026, the Malaysian Communications and Multimedia Commission (MCMC) announced that MCMC will cancel the spectrum allocation of 3300-3400MHz in the Class Assignment No.2 of 2025 for UWB equipment. The allocation table has stipulated that the allocation of the 3400-3700Mz band will be valid until May 31, 2025, so from April 1, 2026, UWB equipment will not be able to use the 3300-3700MHz frequency band in Malaysia, and the frequency band can be used is 3700-10600MHz.

Nigeria 奈及利亞

奈及利亞發布《2026 年 6 GHz (5925 – 6425) MHz 頻段低頻段使用框架》和《2026 年 60GHz 頻段多千兆無線網路使用指南》

奈及利亞發布《2026 年 6 GHz (5925 – 6425) MHz 頻段低頻段使用框架》和《2026 年 60GHz 頻段多千兆無線網路使用指南》。

Nigeria publishes Framework for the use of the lower part of the 6 GHz (5925 – 6425) MHz band 2026 and Guidelines for the Use of the 60GHz Band for Multi Gigabit Wireless 2026.

Philippines 菲律賓

菲律賓擬發佈行動電源和可攜式電源組產品認證許可技術規定

[法規草案] 2026年2月27日，菲律賓DTI提交G/TBT/N/PHL/357號通報，計畫發佈行動電源和可攜式電源組強制性產品認證技術規定草案。該草案旨在嚴格確保在菲律賓進口、製造、分銷或銷售的行動電源和可擕式電源組符合規定的安全要求。
適用範圍:
由直流電源供電，或通過直接插接結構由交流市電電源供電的行動電源及可攜式電源裝置；提供直流輸出的行動電源；可攜式電源裝置，包括但不限於搭電線元件、插座、直流電連接器、車載適配器插座、USB連接器以及感應式電力發射器等
PS認證計畫:
法規提到，PS安全認證標誌許可計畫 (PS Safety Certification Mark Licensing Scheme，簡稱為PS許可計畫) 將面向在菲律賓市場銷售或分銷行動電源 (充電寶) 及可擕式電源裝置的本地和國外製造商/組裝商開放。對於符合相關要求的公司，將授予PS許可標誌。
持有有效PS許可證的本地公司：年度工廠審核+市場隨機抽檢。
持有有效PS許可證的外國公司：年度工廠審核+每批次貨物到貨檢驗。
進口商品清關 (ICC) 認證標誌計畫:
適用於未獲PS認證的行動電源 (充電寶) 及可攜式電源裝置的進口商，僅對當次報關批次有效，需逐批申請。
注意事項:
每份PS許可證申請均須針對特定工廠、生產設施或場地提出。若申請人為境外製造商/組裝商，必須由境外製造商/組裝商在菲律賓合法註冊的本地分支機搆、代表處或代理機構提交申請。凡進口由外國製造商/組裝商獲得有效PS許可證所涵蓋的行動電源和可攜式電源設備的企業，均需根據每批貨物、每份提單/航空貨運單的情況申請確認聲明(SOC)，以確保所進口的產品源自持有有效PS許可證的公司。
PS許可證自簽發之日起生效，有效期為3年。

On 27 February 2026, Department of Trade and Industry of Bureau of Philippine Standards, published Draft Technical Regulation for the Mandatory Product Certification of Power Banks and Portable Power Pack.
This DAO aims to strictly ensure that power banks and portable power packs to be imported, manufactured, distributed, or sold in the Philippines meet the specified safety requirements.
This Technical Regulation prescribes the mandatory product certification of power banks and portable power packs whether locally manufactured or imported, as follows:
– Power banks and portable power packs devices with an input voltage supplied by DC power source with rated maximum up to 60 Vdc, or by an AC mains power source through direct plug in construction;
– Power banks that provide DC output(s) with rated maximum up to 60 Vdc;
– Portable power packs with at least one output option such as, but not limited to booster cable assemblies, receptacles, DC connectors, vehicle adapter sockets, USB connectors, and induction power transmitters. Additional outputs are not restricted;
– Power banks and portable power packs with integral photovoltaic cells as a power source; and
– Power banks and portable power packs that are incorporated with and/or forms integral part of another device

Saudi Arabia 沙烏地阿拉伯

SASO 推遲實施 USB Type-C 測試報告的要求至2026年5月1日

SASO 已決定推遲實施 USB Type-C 測試報告的要求。在 2026 年 5 月 1 日之前，仍可接受企業自行聲明作為符合 USB Type-C 要求的證明。

SASO has decided to postpone the implementation of the requirement to provide USB Type-C test reports. Until 1 May 2026, a self-declaration will continue to be accepted as proof of compliance with the USB Type-C requirements.

Saudi Arabia 沙烏地阿拉伯

沙烏地阿拉伯發布《網路安全服務、產品和解決方案許可監管框架》

沙烏地阿拉伯發布了《網路安全服務、產品和解決方案許可監管框架》。該框架旨在透過明確被授權者的責任和義務，規範沙烏地阿拉伯境內網路安全服務和產品的供應，從而提升此類服務、產品和解決方案在交付給各類實體時的效率和品質。

Saudi Arabia issued Regulatory Framework for Licensing Cybersecurity Services, Products and Solutions.
This Framework aims to regulate the provision of cybersecurity services and products in the Kingdom through a regulatory framework that defines the responsibilities and obligations of the licensee, contributing to promoting the efficiency and quality of such services, products, and solutions during their delivery to various entities.

Singapore 新加坡

新加坡發布蜂窩行動終端技術規範

2026年3月6日，新加坡資訊通信媒體發展局 (IMDA) 發佈了蜂窩移動終端技術規範 (IMDA TS CMT Issue 1 Rev 4)。該技術規範的更新內容包括：
自2026年12月31日起，所有手機必須預設禁用2G網路；
自2026年4月1日起，所有手機必須具備緊急社區廣播功能；
在上述日期之前達到產品生命週期結束 (EOL) 的設備不受上述要求的約束。

On March 6, 2026, the Infocomm Media Development Authority (IMDA) of Singapore published the Technical Specification for Cellular Mobile Terminals (IMDA TS CMT Issue 1 Rev 4). Updates to the specification include:
From December 31, 2026, all phones must disable 2G networks by default;
From April 1, 2026, all mobile phones must have emergency community broadcasting functions;
Devices that reach the end of product life (EOL) before the above date are not subject to the above requirements.

Singapore 新加坡

新加坡網路安全局與日本經濟產業省相互認可物聯網網路安全計畫

新加坡網路安全局 (CSA)於2026年3月18日發佈新聞稿，宣佈CSA與日本經濟產業省 (METI) 已簽署合作備忘錄 (MoC)，相互認可物聯網網路安全認證體系CLS和JC-STAR。該合作備忘錄將於2026年6月1日起生效。

Singapore CSA and Japan METI Mutually Recognize IoT Cybersecurity Schemes
The Cyber Security Agency (CSA) of Singapore issued a press release on March 18, 2026, announcing that CSA and the Ministry of Economy, Trade, and Industry (METI) in Japan have signed a Memorandum of Cooperation (MoC) to mutually recognize IoT cybersecurity labelling schemes CLS and JC-STAR. This MoC will take effect starting June 1, 2026.

Singapore 新加坡

新加坡網路安全局更新家用路由器強制性要求

新加坡網路安全局 (CSA) 於2026年3月2日發佈新聞稿，宣佈CSA與資訊通信媒體發展局 (IMDA) 將於2027年底前，將家用路由器的強制性網路安全要求從“網路安全標籤計畫”一級提升至二級。

Singapore CSA Updates Mandatory Requirements for Residential Routers
The Cyber Security Agency (CSA) of Singapore issued a press release on March 2, 2026 announcing that CSA and Infocomm Media Development Authority (IMDA) will raise mandatory cybersecurity requirements from Cybersecurity Labelling Scheme Level 1 to Level 2 for residential routers by the end of 2027.

South Korea 韓國

韓國MSIT發佈2026-9號公告提高6GHz Wi-Fi功率限值

2026年2月10日，韓國科學技術資訊通信部 (MSIT) 發佈了2026-9號公告，修訂了免許可無線電設備的技術標準，以支援工業基礎設施建設並提升用戶便利性。其中主要修訂如下：
Wi-Fi 7 (6GHz 頻段): 提高室內和地鐵環境6GHz頻段功率限制，以增強高速連接，其中在5925-6425MHz頻段，室內和地鐵車廂內允許1W EIRP，此前該頻段僅允許0.5W EIRP；在6425-7125MHz頻段室內環境仍然允許0.5W EIRP；
高級藍牙：更新技術標準，納入最新藍牙技術使用的新型無線電傳輸格式；
超寬頻 (UWB) 與定位：完善超寬頻 (UWB) 和定位技術的要求，以確保資料傳輸的準確性和節能性。

On February 10, 2026, South Korea’s Ministry of Science and ICT (MSIT) issued Announcement No. 2026-9, revising the technical standards for license-exempt radio equipment to support industrial infrastructure construction and improve user convenience. The main revisions are as follows:

Wi-Fi 7 (6GHz band): Increased power limits for indoor and metro environments to enhance high-speed connectivity, with 1W EIRP allowed indoors and in subway cars in the 5925-6425MHz band, compared to the previous 0.5W EIRP in this band; 0.5W EIRP remains unchanged in the 6425-7125MHz band indoor environment;
Advanced Bluetooth: Updated technical standards to include new radio transmission formats used by the latest Bluetooth technology;
Ultra-wideband (UWB) and positioning: Improve the requirements of ultra-wideband (UWB) and positioning technology to ensure the accuracy and energy efficiency of data transmission.

Vietnam 越南

越南提出貨物和產品可追溯性規定的通知草案

[法規草案] 越南提出工貿部管轄範圍內貨物和產品可追溯性規定的通知草案。
該草案要求貿易商/進口商註冊高風險產品並產生二維碼以確保可追溯性。
該草案徵求意見截止日期為2026年4月20日。

Vietnam proposes Draft Circular stipulating regulations on traceability of goods and products under the management of Ministry of Industry and Trade.
It requires the trader/importer to register the high risk products and generate QR code to ensure traceability.
The draft receives comments till Apr-20 fo 2026.

Ukraine 烏克蘭

烏克蘭批准伺服器和資料儲存產品生態設計要求的技術法規

烏克蘭發布第160/2026號法令，批准伺服器和資料儲存產品生態設計要求的技術法規。該法規依據歐盟第2019/424號條例制定。

Ukraine publishes Decree No. 160/2026 to approve Technical Regulation on Ecodesign Requirements for Servers and Data Storage Products. It is developed based on Regulation (EU) 2019/424.

India 印度

印度 BIS 發佈 IS/IEC 62368-1:2023 換版執行指南草案

[法規草案] 2026年3月9日，印度標準局 (BIS)，根據印度電子和資訊技術部（MeitY）2025年10月29日的公告，發佈IS/IEC 62368-1:2023（音視頻、資訊及通訊科技設備安全要求）新標準的實施指南草案，該標準將取代舊有的 IS 13252 (Part 1):2010 及 IS 616:2017 。
關鍵時間表：並行期與截止日
BIS 針對不同產品類別設定了兩類不同的過渡期限：
1. 擴增實境/虛擬實境 (Extended Reality) 產品
適用物件： AR/VR/MR 設備 。
並行期截止日： 2026年5月1日 。
2. 其他 38 類電子資訊產品
適用物件： 筆記型電腦、手機、電視、電源適配器、印表機、伺服器、智慧手錶、藍牙喇叭等 。
並行期截止日： 2028年11月1日 。
執行指南核心要點
• A. 現有執照持有人 (Existing Licensees)
1.測試要求： 必須針對執照範圍內的所有主檢型號 (Lead Models)，提交由 BIS 認可實驗室出具的 IS/IEC 62368-1:2023 完整測試報告 。
2.系列型號聲明： 需提供承諾書，確認系列中的其他型號也符合新標準要求 。
3.關聯標準：
o電視機： 若更換標準影響到 IS 18112:2025 的合規性，需一併提交相關報告 。
o手機： 若影響到 IS 16333 (Part 3):2022（印度語言支援），需提交相關報告 。
oCCTV： 若影響到 IP 攝像機安全要求，需提交相關報告 。
o注：若無影響，則提交不相關聲明即可 。
• B. 新申請人 (New Applicants)
1.受理規範： 目前仍可選擇按舊標準或新標準申請 。
2.轉換承諾： 若選擇按舊標準申請，必須提交聲明，保證在並行期截止日前完成新標準轉換 。
3.硬性截止： 超過各類別規定的截止日後，BIS 將不再核發舊標準執照 。
• C. 擴展執照範圍 (Change in Scope)
1.增加型號的申請必須在轉換完成前或並行期截止日前 (以較早者為准) 按舊標準辦理，否則必須直接符合新標準

On March 9, 2026, the Bureau of Indian Standards (BIS), based on a notice issued by the Indian Ministry of Electronics and Information Technology (MeitY) on October 29, 2025, released a draft implementation guide for the new standard IS/IEC 62368-1:2023 (Safety Requirements for Audio-Visual, Information and Communication Technology Equipment). This standard will replace the older IS 13252 (Part 1):2010 and IS 616:2017.
Key Timeline: Parallel Period and Deadline
BIS has set two different transition periods for different product categories:
1. Augmented Reality/Virtual Reality (AR/VR/MR) Products
Applicable to: AR/VR/MR devices.
Parallel Period Deadline: May 1, 2026.
2. Other 38 Categories of Electronic Information Products
Applicable to: Laptops, mobile phones, televisions, power adapters, printers, servers, smartwatches, Bluetooth speakers, etc.
Parallel Period Deadline: November 1, 2028.
Key Points of the Implementation Guidelines
• A. Existing Licensees
1. Testing Requirements: A complete test report for IS/IEC 62368-1:2023, issued by a BIS-accredited laboratory, must be submitted for all lead models within the scope of the license.
2. Series Model Declaration: A commitment letter confirming that other models in the series also comply with the new standard requirements is required.
3. Relevant Standards:
o Televisions: If the standard change affects compliance with IS 18112:2025, a relevant report must be submitted.
o Mobile Phones: If it affects IS 16333 (Part 3):2022 (Indian language support), a relevant report must be submitted.
o CCTV: If it affects IP camera security requirements, a relevant report must be submitted.
Note: If there is no impact, submit an irrelevant declaration.
• B. New Applicants
1. Processing Guidelines: Applications can still be submitted under either the old or new standard.
2. Conversion Commitment: If applying under the old standard, a declaration must be submitted guaranteeing completion of the conversion to the new standard before the parallel period deadline.
3. Hard Deadline: After the deadline specified for each category, BIS will no longer issue licenses under the old standard.
• C. Change in Scope
1. Applications adding models must be processed under the old standard before the conversion is completed or before the parallel period deadline (whichever is earlier); otherwise, they must directly comply with the new standard.

India 印度

關於公共採購 (優先採購印度製造產品) 令 (PPP-MII) 中閉路電視攝影機測試要求的澄清

2026年2月4日，印度電子資訊技術部 (MeitY) 發佈通告，透過整合「印度製造優先令」(PPP-MII) 和「強制註冊令」(CRO) 這兩個獨立的監管框架，簡化了閉路電視攝影機的安全合規流程。
• 核心監管更新：統一測試標準：由於CRO和PPP-MII下的安全基本要求 (ER) 相同，因此，為CRO註冊簽發的STQC測試報告現已正式適用於PPP-MII合規。
• 授權機構：所有安全測試必須由STQC局或MeitY指定的機構進行。
• 有效期限：STQC簽發的安全測試報告自簽發之日起有效期限為三年。
• 範圍限制：STQC簽發的安全認證僅限於技術合規性，與PPP-MII要求的本地增值計算無關。

On February 4, 2026, MeitY circular streamlines the security compliance process for CCTV cameras by aligning two separate regulatory frameworks: the PPP-MII Order (Preference to Make in India) and the CRO (Compulsory Registration Order).
• Core Regulatory Updates: Unified Testing Standard: Since the Essential Requirements (ERs) for security are identical under both CRO and PPP-MII, STQC test reports issued for CRO registration are now officially applicable for PPP-MII compliance.
• Authorized Agency: All security testing must be conducted by the STQC Directorate or a MeitY-notified agency.
• Validity Period: Security test reports issued by the STQC remain valid for three years from the date of issuance.
• Scope Limitation: Security certifications issued by STQC are strictly for technical compliance and have no linkage to the calculation of local value addition required under PPP-MII.

Israel 以色列

以色列關於單相16A及以下插頭和插座的強制性標準SI 32第1.1部分第三次修訂將在2026年8月8日生效

關於單相16A及以下插頭和插座的強制性標準SI 32第1.1部分第三次修訂已在以色列官方公報政府公告欄第12252號發布，並將於2026年8月8日生效。

The third amendment to the Mandatory Standard SI 32 part 1.1, dealing with plugs and socket-outlets for single-phase up to 16A, was published in the Israel Official Gazette, Section of Government Notices, no. 12252, and will enter into force on 8 August 2026.

South Korea 韓國

電氣用品及生活用品安全管理運作要領修訂公告_Safety部分物件分類調整

韓國KATS今日發佈編號2026-56國家技術標準公告，2026年4月1日開始KC安規以下幾個產品產品分類出現變更：
吸塵器大類 (吸塵器、蒸汽清洗機、高壓清洗機等)，洗衣機和脫水機大類 (洗衣機、脫水機、洗烘一體機)，電磁爐，烘乾機大類 (烘乾機、烘手機、衣物管理機等)，衛生間用電器大類 (智慧馬桶、智慧坐便器等) 從安全認證物件改成安全確認物件。
改為安全確認之後，這些產品在申請KC safety認證時不需要廠檢。

The Korean Agency for Technology and Standards (KATS) has issued National Technical Standards Notice No. 2026-56. Starting from 1 April 2026, the KC safety regulatory classification for the following product categories has been revised:
• Vacuum cleaner category (including vacuum cleaners, steam cleaners, high-pressure cleaners, etc.)
• Washing machine and spin dryer category (including washing machines, spin dryers, washer-dryer combo units)
• Induction cooktops
• Dryer category (including dryers, hand dryers, garment care appliances, etc.)
• Bathroom electrical appliances (including smart toilets, electronic bidet seats, etc.)
These products have been reclassified from Safety Certification to Safety Confirmation.
Afte being reclassified under Safety Confirmation, these products will no longer require factory inspection when applying for KC safety certification.

Oman 阿曼

阿曼個人電動代步工具 (電動滑板車) 技術法規

阿曼標準化與計量總局 (DGSM) 已於 2025 年 10 月 30 日 通過了個人電動代步工具的技術要求，適用於以下產品類別：
1.無座椅電動滑板車 (包括具可拆卸座椅的滑板車)
2.有或無座椅的自平衡交通工具 (如平衡車)
3.有或無座椅的電動獨輪車
4.配件與元件 (如電池、充電器／轉接器)
進口商必須為每批貨物出具 符合性聲明 (Declaration of Conformity)。
產品在投放市場前，必須依照法規要求標示 海灣合格評定標誌 (GCTS)。
• 生效日期：2026 年 1 月 1 日
• 強制實施日期：2026 年 4 月 30 日
• 已經在市場上產品過渡期結束：2027 年 4 月 30 日

The Oman Directorate General of Standardization and Metrology (DGSM) adopted on 30 October 2025 the technical requirements applicable to specific categories of personal electric mobility devices. The regulation covers the following products:
1.Electric scooters without a seat, including scooters with detachable seats
2.Self-balancing transport devices with or without a seat (e.g., hoverboards)
3.Electric mono-wheels with or without a seat
4.Electric skateboards
5.Accessories and components (such as batteries and chargers/adapters)
Importers are required to issue a Declaration of Conformity for each shipment.
Products must bear the Gulf Conformity Tracking Mark (GCTS) in accordance with the regulation before being placed on the market.
• Effective date: 1 January 2026
• Mandatory application: 30 April 2026
• Transitional period for products already in the market ends: 30 April 2027

家用電器 House Appliances

Saudi Arabia 沙烏地阿拉伯

沙烏地阿拉伯發佈SASO 2885:2025 (電動洗衣機能效和水效) 的新草稿版本

[法規草案] 沙烏地阿拉伯標準組織 (SASO) 就 SASO 2885:2025“電動洗衣機-能效和用水性能要求及標籤””向世界貿易組織 (WTO) 發佈了通知。
本通知涉及 沙烏地阿拉伯標準 SASO 2885 的新修訂草案，標題為“電動洗衣機——能效和用水性能要求及標籤”。該草案納入了根據此前已通知的 Rv1 版本標準收到的意見而作出的修訂。該標準規定了容量不超過 25 公斤的市電供電式洗衣機和洗烘一體機的最低能效要求 (MEPS)，以及測試、計算和標籤程序，包括嵌入式洗衣機、多桶洗衣機和洗烘一體機。該標準還涵蓋市電供電但也可由電池供電的電器。
最終意見徵集截止日期為 2026 年 5 月 12 日。

SASO issued WTO notification regarding SASO 2885:2025 – “”Electrical Clothes Washing Machines – Energy and Water Performance Requirements and Labelling
This notification concerns new draft revision of Saudi Standard SASO 2885, titled: “”Electrical Clothes Washing Machines – Energy and Water Performance Requirements and Labelling.””This draft incorporates revisions made in response to comments received on the previously notified Rv1. version of the standard.The standard specifies the Minimum Energy Performance Requirements (MEPS) as well as the testing, calculation, and labelling procedures for electric mains-operated washing machines and washer-dryers with capacities up to 25 kg, including built-in units, multi-drum washing machines, and washer-dryers. The scope also includes appliances that are mains-operated but can additionally be powered by batteries.
The final comment date is 12 May 2026.

能源效率要求 Energy Efficiency Requirements

EAEU 歐亞經濟聯盟

EAEU發佈能效法規TR EAEU 048/2019的更新草案公眾諮詢

[法規草案] 2026年3月5號，EAEU發佈了能效法規TR EAEU 048/2019的更新草案公眾諮詢：Draft Amendments No. 1 to the Technical regulation of the Eurasian Economic Commission «On Requirements to Energy Efficiency of Energy Consuming Devices»。評論日期截止2026年5月8號，批准及生效日期待定。

EAEU published draft amendments No. 1 to the Technical regulation of the Eurasian Economic Commission «On Requirements to Energy Efficiency of Energy Consuming Devices» (TR EAEU 048/2019.The final date for comments is 8 May 2026. Proposed date of adoption and proposed date of entry into force is to be determined at a later time.

Taiwan 台灣

臺灣發布《空氣壓縮機最低能效標準及能效等級標籤和檢驗要求》修訂草案

[法規草案] 經濟部標準檢驗局 (BSMI)預告修正「空氣壓縮機容許耗用能源基準與能源效率分級標示」相關規定。
-擴大管制範圍：出口壓力管制範圍調整
-基準調整：提高可變轉速迴轉式空壓機能效基準，並新增液冷式產品的計算公式 。
-行政優化：刪除光碟檢送方式，推行電子化申請，並加強主管機關抽樣檢測與見證測試的權限 。
-文字修正：明確規範對象為供國內使用者，並將「公司」修正為「廠商」以符合法規體例 。
根據公告內容，目前處於草案預告階段。對公告內容有意見者，請於公告刊登隔日起 60 日內 (即 2026 年 5 月中旬前) 陳述意見。

The Ministry of Economic Affairs announced draft amendments to energy efficiency standards for air compressors on March 11, 2026. Key updates include:
-Expanded Scope: Adjusting the discharge pressure range
-Enhanced Standards: Raising the Minimum Energy Performance Standards (MEPS) for variable-speed rotary compressors and introducing calculation formulas for liquid-cooled models.
-Administrative Changes: Discontinuing the use of CD-ROMs for report submissions in favor of digital processes, and granting authorities the power to perform sampling and witnessed testing before registration.
-Clarifications: Adding “”for domestic use”” to specify the regulated products and standardizing legal terminology (e.g., changing “”company”” to “”manufacturer””).

燈具 / LED Luminaiaries/LED

India 印度

印度發布《IS 16102 (Part 1):2026通用照明用自鎮流LED燈具》實施指南

印度發布了《IS 16102 (Part 1):2026通用照明用自鎮流LED燈具 – 第1部分安全要求》實施指南。自2026年8月3日起，新版標準IS 16102 (Part 1):2026將取代舊版標準IS 16102 (Part 1):2012。
在2026年8月2日的過渡期內，現有許可證/證書持有人和新的許可證/證書申請人應遵循該指南中的說明。

India publishes Guidelines for implementation of IS 16102 (Part 1):2026 Self-Ballasted LED Lamps for General Lighting Services – Part 1 Safety Requirements. Starting from Aug-3 of 2026, new version standard IS 16102 (Part 1):2026 will replace old version standard IS 16102 (Part 1):2012.
During transition period by Aug-2 of 2026, the existing licensees/certfication holders and new applicants for licence/certificate shall follow instructions in the guidelines.

其他 / 多主題產品 Others / Products with Multiple Subjects

EAEU 歐亞經濟聯盟

歐亞經濟聯盟公佈須遵守可追溯性機制的商品清單

歐亞經濟聯盟公佈了進口到歐亞經濟聯盟關卡的商品清單，這些商品須遵守可追溯性機制。歐亞經濟聯盟內部的可追溯性機制將於2026年9月1日全面生效。
新增的受監管商品清單包括:
-家用冰箱和冰櫃
-洗衣機
-顯示器、投影機和電視設備
-嬰兒推車和汽車安全座椅
-專用設備 (推土機、挖土機、裝載機)
其他強制性商品清單可在歐亞經濟聯盟海關總署 (Chestny ZNAK) 官方網站查詢。列入強制清單的商品必須符合可追溯性要求。

EAEU published list of goods imported into the customs territory of the Eurasian Economic Union subjects to traceability mechanism. The traceability mechanism within the EAEU will come into full operation on September 1, 2026.
The newly-added regulated list of products includes:
Household refrigerators and freezers.
Washing machines.
Monitors, projectors and TV equipment.
Baby strollers and car seats.
Special equipment (bulldozers, excavators, loaders)
Other products can be found in the Chestny ZNAK official website. Products fall into the mandatory list need to comply with the traceability requirement.

Ukraine 烏克蘭

烏克蘭發布命令以修訂機械技術法規標準清單

烏克蘭發布第2687/2026號命令，修訂機械技術法規標準清單。該令與歐盟委員會第2026/80號實施決定一致。

Ukraine publishes Order No.2687/2026 to amend standard list of Technical Regulation on Machinery. The Order is aligned with Commission Implementing Decision (EU) 2026/80

UK 英國

英國預計繼續對機械設備認可包括CE標誌在內的某些歐盟要求

自2021年1月1日起，英國繼續認可帶有CE標誌的機械設備以及帶有UKCA (英國合格評定) 標誌的機械設備，適用於投放英國市場的相關產品。這種做法使得企業在向英國市場投放產品時可以選擇使用其中一種產品標誌。英國政府正在引入《2026年機械供應 (安全) (修訂和過渡條款) 條例》(簡稱 “2026年英國條例”)，以繼續認可包括CE標誌在內的某些歐盟要求，從而使符合這些要求的機械設備能夠在滿足特定條件的情況下投放英國市場。這將反映歐盟機械指令的變更。透過該立法擴大CE認可範圍將適用於英國 (英格蘭、蘇格蘭和威爾斯)。

Since 1 January 2021, the UK has continued to recognise CE marked machinery equipment alongside the UKCA (UK Conformity Assessed) marked machinery, for relevant products placed on the GB market. This approach has enabled businesses to use either product marking when placing goods on the GB market. The UK Government (UKG) is introducing the Supply of Machinery (Safety) (Amendment and Transitional Provisions) Regulations 2026 (‘the GB Regulations 2026)’ to continue recognition of certain EU requirements including the CE marking so that machinery meeting these requirements can be placed on the Great Britain (GB) market, subject to certain conditions. This will reflect the changes to the EU machinery directive.The extension of CE recognition through this legislation will apply to Great Britain (England, Scotland, and Wales).

India 印度

印度公佈8項品質控制令的修訂

印度公佈了對8項品質控制令的修訂，其中規定，凡在「Udyam門戶網站」註冊的微型、小型和中型企業部可免於認證的條件。
– 火焰打火機 (品管) 令，2023年
– 飲用水瓶 (品質管制) 令，2024年
– 焊條和焊條 (品質控制) 令，2023年
– 家用保溫瓶、保溫壺和保溫容器 (品質控制) 令，2024年
– 電吊扇 (品管) 令，2023年
– 實驗室玻璃器皿 (品質管制) 令，2023年
– 空氣冷卻器和空氣過濾器 (品質控制) 令，2025年
– 傢俱 (品質控制) 令，2025年

India publishes amendments to 8 Quality Control Orders, it exempts certification for an enterprise, registered under Udyam Portal of the Ministry of Micro, Small and Medium Enterprises, wherein the investment in plant and machinery or equipment at original cost does not exceed rupees one crore and the turnover do not exceed rupees five crore for the previous financial year as certified by a Chartered Accountan.
– Flame-Producing Lighters (Quality Control) Order, 2023
– Potable Water Bottles (Quality Control) Order, 2024
– Welding Rods and Electrodes (Quality Control) Order, 2023
– Insulated Flask, Bottles and Containers for Domestic Use (Quality Control) Order, 2024
– Electric Ceiling Type Fans (Quality Control) Order, 2023
– Laboratory Glassware (Quality Control) Order, 2023
– Air Cooler and Air Filters (Quality Control) Order, 2025
– Furniture (Quality Control) Order, 2025

India 印度

印度 Meity 對高度專業化設備 (HSE) 定義且進口/製造量極低的產品發布指令

Meity於2026年3月12日 公告 ⟪Procedure for issuance of exemption for Highly Specialized Equipment (HSE) under the Electronics and Information Technology Goods (Requirements for Compulsory Registration) Order, 2021.⟫ ，適用於符合 高度專業化設備 (HSE) 定義且進口/製造量極低的產品 。
生效日期: 2026年6月15日 起正式實施 。
HSE 判定標準: 設備必須同時滿足「數量限制」與「技術指標」任一項:

申請要點:

提醒: 透過 ICEGATE 門戶網站使申請流程更加精簡，但也強化了品牌方在授權證明、檔齊備性及數量追蹤方面的嚴格責任 。
• 總量管制: 100 台的限額是計算該型號在全球所有產地進入印度的總和 。
• 轉制要求: 一旦該年度進口量達到 100 台，Meity 將停止核發豁免，後續必須取得正式的 BIS 註冊 。
• 清關連動: 豁免信將直接透過 ICEGATE 系統傳輸，海關將以此為憑放行 。

MeitY Circular dated 12.03.2026: “”Procedure for issuance of exemption for Highly Specialized Equipment (HSE) under the Electronics and Information Technology Goods (Requirements for Compulsory Registration) Order, 2021.”” This applies to products that meet the definition of Highly Specialized Equipment (HSE) and are imported or manufactured in very low volumes.
Effective Date: Effective from 15th June, 2026.
HSE Qualification Criteria: Equipment must satisfy both the “”Quantity Limit”” and any one of the “”Technical Requirements””:

Application Key Points:

Reminder: While the process is more streamlined through the ICEGATE portal, it also introduces stricter accountability for brands regarding authorization, documentation, and quantity tracking.
•Total Quantity Control: The quantity limit of 100 units is counted across the regulatory model number from all locations.
•Registration Requirement: Once the exemption quantity reaches 100, MeitY will cease issuing exemptions, and the manufacturer must obtain BIS Registration.
•Customs Integration: Exemption letters are issued through the ICEGATE portal, and Customs shall allow imports based on these letters.

 

Israel 以色列

以色列經濟部澄清雷射筆的合規需求

以色列經濟部進口管理局澄清，儘管雷射筆進口程式中對專業用途的1-2類雷射筆有所規定，但實際上並不需要工業標準協會 (SI) 對產品風險等級的認證，只需提供標籤和標記測試合格證書即可。

The Import Administration at the Ministry of Economy clarifies that despite what is stated in the Laser Pointer Import Procedure, regarding laser pointers in categories 1-2 for professional use, the Standards Institution of Industry’s approval for the risk level of the product is not required, but only a certificate of compliance with the labeling and marking tests.

Taiwan 台灣

臺灣發布修訂“強制檢驗項目參考商品分類代碼 (資料傳輸設備和玩具)

經濟部標準檢驗局 (BSMI) 公告修正應施檢驗商品之參考貨品分類號列，涉及「資料傳輸設備」(如路由器、交換器等，排除醫療器材及電信終端設備) 及「玩具」兩類產品。此次修正係配合經濟部國際貿易署調整進出口貨品號列，新增及刪除部分分類號列，並同步更新相關檢驗適用範圍。此變更屬於分類號列調整，並未改變原有檢驗義務，但將影響報驗及通關作業。

The Bureau of Standards, Metrology and Inspection (BSMI), under the Ministry of Economic Affairs (MOEA), has revised the reference commodity classification codes for mandatory inspection items, covering “data transmission equipment” (e.g., routers, switches, excluding medical devices and telecom terminal equipment) and “toys.” The revision aligns with updates made by the International Trade Administration, including the addition and removal of specific HS codes and corresponding import regulations. While the inspection scope remains unchanged, the update affects customs declaration and clearance procedures.