资讯 / 电信 ITE / Telecom

Brazil 巴西

2022 年 3 月 31 日，巴西国家计量、标准化和工业质量研究所 (INMETRO/CONMETRO) 发布了 第148号协议，批准家用电器合格评定技术要求。已于 2022 年 5 月 2 日获得认证的家用和类似器具必须在 2027 年 5 月 2 日之前根据附件中规定的适用条件和安排，在产品上采用合规标识印章。本协议于 2022 年 5 月 2 日生效。

On 31 March 2022, the Brazil National Institute of Metrology, Standardisation and Industrial Quality (INMETRO/CONMETRO) published Portaria No. 148 to approve Technical Requirements for Conformity Assessment of Household Electrical Appliances.

This Portaria approves the safety and labelling rules for household and similar appliances, in the form of the Conformity Assessment Requirements and the Specifications for the Conformity Identification Mark, contained in Annexes I and II.

Families of household and similar appliances that are already certified on 2 May 2022 must adopt, by 2 May 2027, the Compliance Identification Seal, affixed on the product, according to the applicable conditions and layout established in Annex II.

Manufacturers and importers of families of household appliances that are already certified must adapt, by 2 May 2025, the certification processes in order to meet, on the packaging, the label conditions and layout established in Annex II.

This Portaria will enter into force on 02 May 2022.

Note: until 31 December 2024, ABNT NBR NM 60335-1:2010 – Safety of Home Appliances and Similar, Part 1: General Requirements – and their respective particular rules; and IEC 60335-1:2006 (Ed. 4.2) – Household and similar electrical appliances – Safety – Part 1: General Requirements, and their respective particular standards, may be followed. After 31 December 2024, only IEC 60335-1:2016 (Ed. 5.2) and its corresponding particular standards, listed in sub-item 3.1, will be accepted.

 

2022 年 1 月 19 日，巴西国家计量、标准化和工业质量研究所 (INMETRO/CONMETRO) 发布第9号协议，以批准适配器插头和插座的合格评定要求。

该协议适用于插头和插座适配器，或执行插头和插座适配器功能的任何设备，用于家用和类似用途，电压高达 250V，电流高达20A，带或不带百叶窗，带或不带保险丝，专用于交流电。

已获得认证的插头和插座适配器系列的制造商和进口商应有 36 个月的时间来调整认证流程，以满足包装上的适用条件和合格标识印章的要求。

本协议于 2022 年 2 月 1 日生效，并废除第 324/2007 号、第 82/2008 号和第 251/2009 号协议。

On 19 January 2022, Brazil’s National Institute of Metrology, Standardization and Industrial Quality (INMETRO/CONMETRO) published Portaria No. 9 to approve the requirements for Conformity Assessment of Adapter Plugs and Sockets.

The Portaria applies to plug and socket adapters, or any equipment that performs the function of a plug and socket adapter including the so-called “Benjamin” or “T”, for household and similar use, for voltages up to 250V and current up to 20A, with or without shutters, with or without fuses, and for exclusive use in alternating current.

Manufacturers and importers of plug and socket adapters families that have already been certified shall have 36 months, counted from the abovementioned date, to adapt the certification processes in order to meet, on the packaging, the applicable conditions and layout of the Conformity Identification Seal.

In addition, the Regulation establishes criteria and conformity assessment procedures for plug and socket adapters, through the certification mechanism, certification steps, identification mark and other details focused on safety, aiming at the prevention of accidents in its use.

This Portaria will come into force on 1 February 2022 and will repeal Portarias No. 324/2007, No. 82/2008 and No. 251/2009.

 

Malaysia 马来西亚

2022 年 3 月，SIRIM/MCMC 公布所有IMT-2020 (第五代) – 蜂窝助推器设备和全球移动通信和长期演进系统的新申请和续订申请程序。

SIRIM and Malaysian Communications and Multimedia Commission (MCMC) has approved and published Technical Codes for IMT-2020 (FIFTH GENERATION) – CELLULAR BOOSTER EQUIPMENT and GLOBAL SYSTEM FOR MOBILE COMMUNICATIONS AND LONG-TERM EVOLUTION – CELLULAR BOOSTER EQUIPMENT last year August.

On March 2022 , SIRIM/MCMC had announce the procedure for the new application and Renewal application for all related product. Below are the information:

New Application

Pursuant to that, all GSM, LTE and 5G CBE that are to be imported, distributed, and/or used in Malaysia shall be certified in accordance with these Technical Codes. Thus, all new applications which fulfill the Technical Code and Certification Requirements for Compliance Approval (Type Approval) on Communication, Multimedia and Hybrid Equipment, eTAC/DOC/01-1.1 (“Certification Requirements”) will be granted full approval and are allowed for a maximum validity period of five (5) years.

Renewal Application

Renewal application for existing approval of GSM, LTE and 5G Booster Equipment are no longer allowed. These existing applications will be expired effective immediately. A new application (Normal Application) is required, and it shall meet the new technical code requirements for Cellular Booster Equipment.

 

Malaysia 马来西亚

自 2022 年 2 月 1 日起，马来西亚能源委员会受监管的电气和天然气产品实施新的 SIRIM-ST 标签和二维码。申请人可以完成现有 SIRIM-ST 标签的库存，直到收到带有 QR 码的新 SIRIM-ST 标签。 贴在产品上的没有二维码的 SIRIM-ST 标签仍然有效。

Effective 1 Feb 2022, SIRIM QAS International has implemented new SIRIM-ST labels with QR code for regulated electrical and gas products under the Energy Commission (Suruhanjaya Tenaga or ST) of Malaysia.

SIRIM and ST have introduced this type of label to assist consumer in accessing information of the products through SIRIM Mobile Apps easily and conveniently. It is also one of the methods to confirm authenticity of certification status of the products.

With this implementation, applicants are allowed to finish up stock of existing SIRIM-ST labels until receipt of new SIRIM-ST labels with QR Code. SIRIM-ST labels without QR code which were affixed of the products remain valid.

Note: The new label with QR Code applied to both Consignment and PCS.

 

Mexico 墨西哥

2022 年 6 月 25 日，IFT 将对合格评定程序 (PEC) 进行一些修改。值得注意的是：

1. CoC 可转让，这允许当地墨西哥进口商使用来自其他当地公司的CoC
2. 检测报告的有效期由60天延长至120天，以防止其在认证过程中失效
3. 测试过程中需要的样品数量不同

On June 25, 2022, the IFT will make effective some modifications in the Conformity Assessment Procedure (PEC).

Among the changes it should be noted that:

1. The CoC becomes transferable. This allows local Mexican importers to use CoCs from other local companies.
2. The validity period of the test report is extended from 60 days to 120 days, this to prevent its validity from expiring during the homologation process.
3. The number of samples required during the tests changes.

 

Paraguay 巴拉圭

巴拉圭工业和商业部于 2021 年 12 月 29 日批准第 931 号决议，关于进口移动电话和移动电话设备的要求。该决议自 2022 年 4 月 1 日起生效，至 2022 年 9 月 30 日届满。

On 29 December 2021 Resolution No. 931 which establishes a compliance regime for certain articles of Resolution No. 410/2017 was approved by the Paraguayan Ministry of Industry and Commerce.

The Resolution:

1. Changes point 5.8 of article 5 of Resolution No. 410/2017 to determine the digital presentation for each application for import license for mobile cellular telephone devices of:

1) Certificate of Approval for Cell Phone Devices granted by CONATEL; or

2) Proof of submission of the approval certificate application to CONATEL.

2. Suspends item 9 of article 5 and item 4 of article 7 of Resolution No. 410/2017 on CONATEL’s proof of the IMEI listing record and prior license for the importation of mobile phone devices and non-integrated mother boards of mobile phones, respectively.

This Resolution will enter into force from 1 April 2022 and expire on 30 September 2022.

 

Thailand 泰国

泰国工业部于 2022 年 4 月 4 日发布制定关于音频/视频、信息和通信技术设备的工业标准 TIS 62368/3-2564 – 第 3 部分：在安全方面通过通信电缆和端口传输直流电。

本公告自 2022 年 4 月 4 日起生效，即在政府公报上发布之日。

Published on 4 April 2022 by the Thai Ministry of Industry, this Announcement establishes Industrial Standard TIS 62368/3-2564 on Audio/Video, Information and Communication Technology Equipment – Part 3: Safety Aspects for DC Power Transfer Through Communication Cables and Ports, in accordance with the Industrial Product Standards Act.

The Standard covers equipment intended to supply and receive operating power through communication cables or ports. It provides safety requirements for circuits designed to transfer DC power from the power sourcing equipment (PSE) to the powered device (PD).

This Announcement is effective from 4 April 2022, the date of publication in the Government Gazette.

 

UAE 阿联酋

自 2022 年 1 月起，阿联酋电信和数字政府监管局 (TDRA) 向注册的电信设备制造商或进口商提供的型式批准制度符合性标志已更改。

The Type Approval Regime Conformity Mark that is provided by The Telecommunications and Digital Government Regulatory Authority (TDRA) of the United Arab Emirates to a registered manufacturer or importer of telecommunications equipment has been changed from January 2022.

The United Arab Emirates TDRA notifies that information on the label should correspond to the information that is displayed after scanning the relevant QR code. Moreover, the QR code should lead to the actual landing page, where users can receive both information on the product and a copy of its valid certificate.

The Type Approval Regime Conformity Mark must be affixed on the equipment box and under the display platform of telecommunications equipment in retail stores. It should be clear, readable, and non-removable. If the product is to be sold over the internet, the mark should be available on the website as well.

 

Yemen 也门

也门 MTIT (电信和信息技术部) 在过去几个月暂停颁发证书后终于又开始颁发型式批准。即日起颁发的型式认证有效期为 2 年，当局已撤销有效期为 3 年的初步决定。

Yemen MTIT (Ministry of Telecom & Information Technology) finally started to issue and release type approvals after suspension of issuance for the last few months.

Here is a summary of the changes:

Type approvals will be issued from now on with a validity of 2 years. (The initial decision from the authority with a validity of 3 years has been revoked.

 

Vietnam 越南

2022年3月消息，越南信息和通信部 (MIC) 发布了通知草案2022/TT-BTTTT，后续可能会取代第11/2020/TT-BTTTT号通告和第01/2021/TT-BTTTT号通告。该通告预计于2022年7月1日起施行。

Vietnam MIC has released draft Circular xx/2022/TT-BTTTT to replace the Circular 11/2020/TT-BTTTT and Circular 01/2021/TT-BTTTT stipulating the new list of products under MIC Type Approval and Self-assessment DoC scope which shall take effect from July 01, 2022.

New Changes of the draft Circular xx/2022/TT-BTTTT of Vietnam MIC is as per below :

(1) QCVN 22:2021/BTTTT (for safety of ICT product)

(2) QCVN 65:2021/BTTTT (RF for WLAN 5GHz)

(3) QCVN 123:2020/BTTTT (RF for 40GHz ~ 246GHz SRD)

(4) QCVN 124:2021/BTTTT (RF for 76GHz ~ 77GHz vehicle radar)

(5) QCVN 127:2021/BTTTT (RF for 5G NR SA mobile terminal)

(6) QCVN 129:2021/BTTTT (RF for 5G NR NSA mobile terminal)

A large number of products have been moved from Annex 1 – List of products under TA and DOC list to Annex II – List of products under DoC only including 76~77GHz radar, like RFID 13.56MHz, walkie-talkie, and SHF.

 

 

家用电器 House Appliances

Brazil 巴西

2022 年 3 月 30 日，巴西国家计量、标准化和工业质量研究所 (INMETRO/CONMETRO) 发布了第121号协议，批准家用洗衣机的合格评定要求。

本协议将于 2022 年 5 月 2 日生效。

On 30 March 2022, the Brazil National Institute of Metrology, Standardization and Industrial Quality (INMETRO/CONMETRO) published Portaria No. 121 to approve the conformity assessment requirements for household washing machines.

The conformity assessment requirements and the specifications for the Conformity Identification Seal, in the form of the National Energy Conservation Label (ENCE), are established, respectively, in Annexes I and II.

This Regulation applies to household washing machines of the following types:

• automatic household washing machines with a top opening (top load);
• automatic domestic washing machines with front load;
• automatic domestic washing machines and tumble dryers with top load;
• semi-automatic domestic washing machines;
• automatic washer-dryers with front load;

Industrial or commercial washing machines are excluded from this Regulation.

According to Article 12, manufacturers and importers are accorded a period of 12 months from the effective date of this Portaria to adapt to the provisions of Article 7, as well as to the layout of the Compliance Identification Seal, as established in Annex II.

This Portaria will enter into force on 2 May 2022.

 

Thailand 泰国

2022 年 4 月 4 日，泰国工业部制定了工业标准 TIS 60335/2(90)-2564，关于家用和类似用途电 -安全 – 第 2-90 部分：商用微波炉的特殊要求。

该标准基于 IEC 60335-1，对用于商业用途的微波炉提供安全要求，该微波炉具有腔门，单相器具的额定电压不超过 250 V，其他器具的额定电压不超过 480 V。

本公告自 2022 年 8 月 2 日起生效，自政府公报上公布之日起 120 天。

Published on 4 April 2022 by the Thai Ministry of Industry, this Announcement establishes Industrial Standard TIS 60335/2(90)-2564 on Household and Similar Electrical Appliances – Safety – Part 2-90: Particular Requirements for Commercial Microwave, in accordance with the Industrial Product Standards Act.

The Standard, based on IEC 60335-1, provides safety requirements for microwave ovens intended for commercial use that have a cavity door and a rated voltage not exceeding 250 V for single-phase appliances and 480 V for other appliances.

This Announcement is effective from 2 August 2022, 120 days from the date of publication in the Government Gazette.

 

 

灯具 / LED Luminaiaries/LED

South Korea 韩国

2022 年 4 月 8 日，韩国技术与标准局 (KATS) 批准了《电器和消费品安全控制法操作公告》的修正案。灯具的供电轨道系统被添加到受安全保证的电器清单中，补充现有的固定式灯串、可充电便携式灯、泛光灯和卤素灯具清单。

该通知自2022年10月1日起生效。

On 8 April 2022, the South Korean Agency for Technology and Standards (KATS) approved an amendment to the Operation Bulletin of Electrical Appliances and Consumer Products Safety Control Act.

Electrical Supply Track Systems for Luminaires are added to the list of electrical appliances subject to safety assurance, and as a result the amendment brought changes to the Annexes as follows:

• Adding the said products to the detailed items of lighting equipment subject to safety assurance in Annex 2 (supplements existing list of chain lighting fixtures, rechargeable portable lights, floodlight luminaires and halogen luminaires);
• Adding the model classification and its detailed criteria of the said products to Annex 10;
• Adding a list of parts subject to safety control of the said products to Annex 20;
• Adding safety standard KC 60570 for the products to Annex 25.

The Notice enters into force on 1 October 2022.

 

 

能源效率要求 Energy Efficiency Requirements

澳大利亚 Australia

游泳池泵强制能效等级标签和标准要求将于 2022 年 10 月 起实施。

澳洲能效管理机构GEMS近日公布：从 2022 年 10 月 1 日起销售或供应的所有游泳池泵都需要显示能源等级标签并符合测试要求。 这将帮助消费者通过减少游泳池用电量和减少温室气体排放来节省资金。

游泳池泵的供应商和零售商可以在 2022 年 10 月 1 日之前注册其产品。在此日期之后未在 GEMS 监管机构注册的产品可能不再在澳大利亚境内销售或供应。 我们将与行业、泵供应商、零售商、泳池建造商和其他专业人士合作，就变化和要求进行沟通。

New mandatory standards and labelling requirements for swimming pool pumps

GEMS recently announced: All swimming pool pumps sold or supplied from 1 October 2022 will need to display an energy rating label and meet testing requirements. This will help consumers to save money by reducing the amount of electricity used by their swimming pools and to reduce greenhouse gas emissions.

Suppliers and retailers of swimming pool pumps may register their products prior to 1 October 2022. Products not registered with the GEMS Regulator after this date may no longer be sold or supplied within Australia. We will be working with the industry, pump suppliers, retailers, pool builders and other professionals to communicate the changes and requirements.

 

EAEU 欧亚经济联盟

TR EAEU 048/2019《关于耗能设备能效要求的技术法规》，生效日期将延迟三年至2025年9月1日。

The EEC Council, at the suggestion of the Russian side, decided to postpone the entry into force of the EAEU technical regulation “On requirements for the energy efficiency of energy-consuming devices” to September 1, 2025.

The decision was made as part of the implementation of the list of measures to increase the stability of the economies of the member states of the Eurasian Economic Union, including ensuring macroeconomic stability, approved by Order of the Council of the Commission dated March 17, 2022 No. development and adoption of acts of the second level necessary for the implementation of technical regulations – a list of standards and labels for the energy efficiency of energy-consuming devices.

By the same decision of the EEC Council, the date of entry into force of the decision of the Council of the Commission establishing the forms of labels for energy-consuming devices of various types and the rules for their design was postponed to March 1, 2025. And also the deadline for the entry into force of certain requirements established in Annexes No. 3, 5, 6, 9, 12, 13 and 14 to the technical regulations has been postponed for three years.

 

India 印度

BEE发布通知, 调整现行房间空调 (定速和变速) 能耗标准的有效期至2022年6月30日。

依据修订后的能耗标准，自 2022 年 7 月 1 日起适用，有效期至 2024 年 12 月 31 日。

因此，新标签上显示的有效期应为 2022 年 7 月 1 日至 2024 年 12 月 31 日。

请注意，所有现有型号仅在 2022 年 6 月 30 日之前有效，有效期届满后自动失效。

BEE release the notice regarding the validity of the existing energy consumption standards of Room Air Conditioners (Fixed speed and Variable speed) is valid till 30 June 2022.

In accordance with the provisions of the amendment notification of Room Air Conditioners vide S.O. 4634 (E) dated 10 November 2021, the revised energy consumption standards would be applicable from 1 July 2022 and would be valid till 31 December 2024.

Therefore, the revised validity period to be displayed on the new label shall be from 1 July 2022 to 31 December 2024.

Please note that all the existing models are valid only till 30 June 2022 and will be expired automatically after the expiry of the validity period.

 

India 印度

​BEE 要求 BEE 强制性标准和标签计划涵盖的所有冰箱 (现有无霜冰箱、直冷冰箱类别和即将推出的对开门冰箱类别) 的所有许可证持有者，从2023年1月1日起，在印度生产、进口或销售的每台冰箱都必须贴上二维码和BEE星级标签。

​BEE request all permittees of Refrigerators (existing Frost free refrigerators, Direct Cool refrigerators categories and upcoming side-by-side refrigerator category) covered under BEE’s mandatory Standard & Labelling program are hereby informed that it will be obligatory to affix QR code along with BEE star label on each unit of refrigerator being manufactured, import or sold in India w.e.f. 1st January, 2023.

 

 

其他 / 多主题产品 Others / Products with Multiple Subjects

澳大利亚 Australia

今年6月将开始执行最新的插头与插座标准AS/NZS 3112:2017 +A1:2021。

现在提交的任何证书变更申请或标准升级，都需要同时符合这个最新标准。

The latest plug and pin standard AS/NZS 3112:2017 +A1:2021 will be implemented in June this year.

Any currently submitted certificate for modification or standard upgrades must also comply with this latest standard.

 

Brazil 巴西

2022 年 3 月 25 日，巴西国家计量、标准化和工业质量研究所 (INMETRO/CONMETRO) 发布第102号协议，批准了《用水设备质量和合格评定要求技术法规》。本协议于 2022 年 4 月 1 日生效。

On 25 March 2022, the Brazil National Institute of Metrology, Standardization and Industrial Quality (INMETRO/CONMETRO) published Portaria No. 102 to approve Technical Regulation on Quality and Conformity Assessment Requirements for Water Consumption Equipment.

The Regulation for Water Consumption Equipment was approved in the form of Technical Regulation on Quality, Conformity Assessment Requirements and Specifications for the Conformity Identification Mark, contained in Annexes I, II and III.

This Regulation applies to water consumption equipment of the following types, regardless of the technology applied:

electrical equipment with water cooling and without water quality improvement;

electrical appliances without water cooling and with water quality improvement;

electric equipment with water cooling and water quality improvement;

all non-electrical equipment that has the characteristic of improving the quality of water for human consumption.

The following products are excluded from the application of this Regulation:

equipment that supplies water without cooling and without performing water quality improvement;

filtering elements or water quality improvement devices, which are replacement components;

products intended to improve water quality through a suction process, such as squeeze bottles, straws, among others;

products intended for the treatment of non-potable water;

equipment for the production of ice;

coolers containing a container and/or hydraulic systems for supplying water and ice;

equipment exclusively intended to supply water for the production of tea, coffee, soups, juices and soft drinks.

The equipment is also under a non-automatic import licensing system, and the importer must obtain consent from Inmetro.

This Portaria entered into force on April 1, 2022.

 

Malaysia 马来西亚

2022 年电子烟设备的商品说明 (认证和标记) 令已于 2022 年 4 月 5 日在宪报刊登。本地制造或进口的电子烟装置应在 2022 年 8 月 3 日之前符合商品说明。所有电子烟设备都必须根据 MS 2716:2019 进行测试和认证，其中包括电气、机械、化学、无线连接 (如适用)、EMC 和功能测试。经认证的电子烟装置必须贴上 SIRIM MS 标志，方可销售和提供给市场。

According to The Ministry of Domestic Trade and Consumer Affair (KPDNHEP) of Malaysia, the Trade Description (Certification and Marking) of Electronic Cigarette Devices (vape device) Order 2022 was gazetted on April 5, 2022 under the Trade Description Act 2011.

Locally manufactured or imported e-cigarette device shall comply with the Trade Descriptions by August 3, 2022.

All e-cigarette devices must be tested and certified according to MS 2716:2019 which includes tests of electrical, mechanical, chemical, wireless connectivity (if applicable), EMC and functional.

The certified e-cigarette device shall be labelled with SIRIM MS mark before it can be sold and offered to the market.