2022年3月国际市场准入资讯更新
- Mandatory dates of certification – Phase products 3 remains same for phase 4 products the date has been extended to 1/7/2022.
- ILAC report acceptance date – 30/6/2022 (but it comes with some conditions)
- Phase 3 product list –
- Phase 4 product list –
- Devices without electrical control circuit,
- Equipments with an internal clock frequency of 15 MHz or less,
- Battery devices which are not included in the range of product 1,
- Products with internal clock frequency exceeding 15MHz and below 200MHz,
- Devices with internal clock frequency exceeding 200MHz.
- gas cookers for domestic use;
- household gas ovens;
- household gas cooktops;
- any combination of the three products above.
- Coffee machines;
- Espresso coffee makers;
- Saucepans;
- Bottle heaters;
- Milk heaters;
- Livestock water/feed heaters;
- Sterilisers;
- Egg boilers;
- Laundry boilers;
- Electric Kettles and other appliances for boiling water with a rated capacity not exceeding 10 litres;
- Tea urns;
- Pressure cookers;
- Cooking pots (rice cookers, slow cookers);
- Yoghurt makers;
- Bain-marie glue heaters.
- 可在1个大气压下将水加热到100℃的热水饮水机,应按照IEC 60335-2-15进行检测;
- 不可在1个大气压下将水加热到100℃的热水饮水机,应按照IEC 60335-2-21和/或IEC 60335-2-35进行检测;
- 如果饮水机配有用于分配冷水的压缩机,则须按照IEC 60335-2-24进行检测。
- 现有已注册的饮水机:
- 对于使用不适用的IEC标准进行注册的热水饮水机,宽限期推迟至2023年3月1日。
- 自2023年3月1日起,所有已注册热水饮水机只能使用相应的IEC标准进行更新,其中:可在1个大气压下将水加热到100℃的热水饮水机,仅在提供有效的IEC 60335-2-15检测报告后方可更新;不可在1个大气压下将水加热到100℃的热水饮水机,仅在提供有效的IEC 60335-2-21和/或IEC 60335-2-35检测报告后方可更新。
- 新注册的饮水机:
- 可在1个大气压下将水加热到100℃的热水饮水机,应按照IEC 60335-2-15进行检测;
- 不可在1个大气压下将水加热到100℃的热水饮水机,应按照IEC 60335-2-21和/或IEC 60335-2-35进行检测。
- Existing requirements in the CPSR information booklet
- The requirements for testing and certification of water dispensers under the CPSR as stated in our information booklet are as follows: a. Hot water dispenser which has below boiling temperature shall be tested to either IEC 60335-2-21 (storage type) or IEC 60335-2-35 (instantaneous type).
- Testing to IEC 60335-2-24 shall be required if the water dispenser is incorporated with compressor for dispensing cold water.
- Clarifications regarding the existing requirements
- The Consumer Product Safety Office (CPSO) is aware that there are misinterpretations regarding these requirements, and would like to clarify on the interpretations, in line with decisions laid down by the International Electrotechnical Commission (IEC).
- IEC’s Committee of Testing Laboratories (CTL) decision sheet DSH 579 provides the following clarification on the use of IEC standards for testing and certification of water dispensers: a. IEC 60335-2-15 shall apply if hot water boils
- IEC 60335-2-21 shall apply if hot water does not boil
- IEC 60335-2-35 shall apply if the water heater is instantaneous, and the water does not boil
- The requirements for testing and certification of water dispensers under the CPSR should therefore be interpreted as follows: a. Hot water dispensers which can heat water to 100 °C at 1 atmosphere shall be tested to IEC 60335-2-15
- Hot water dispensers which cannot heat water to 100 °C at 1 atmosphere shall be tested to IEC 60335-2-21 and/or IEC 60335-2-35
- In addition, testing to IEC 60335-2-24 shall be required if the water dispenser is incorporated with compressor for dispensing cold water.
- Existing registered water dispensers
- A grace period will be extended until 1st March 2023 for renewal of hot water dispensers that were registered using a non-applicable IEC standard
- From 1st March 2023 onwards, all currently registered hot water dispensers may only be renewed using the appropriate IEC standard.
- Hot water dispensers which can heat water to 100 °C at 1 atmosphere may only be renewed upon providing valid IEC 60335-2-15 test report
- Hot water dispensers which cannot heat water to 100 °C at 1 atmosphere may only be renewed upon providing valid IEC 60335-2-21 and/or IEC 60335-2-35 test report
- New registrations of water dispensers
- Please be reminded that the following requirements shall continue to be in effect for all new registrations:
- Hot water dispensers which can heat water to 100 °C at 1 atmosphere shall be tested to IEC 60335-2-15.
- Hot water dispensers which cannot heat water to 100 °C at 1 atmosphere shall be tested to IEC 60335-2-21 and/or IEC 60335-2-35.
- luminaires only for mining use;
- luminaires only for indoor use;
- LED projector luminaires of 12, 24, 36 or 48 direct current voltage, which work with solar energy through autonomous photovoltaic panels and batteries, without being connected to the distribution network of the electric company;
- projector luminaires to be used exclusively in explosion-proof areas.
资讯 / 电信 ITE / Telecom
Argentina 阿根廷
阿根廷ENACOM要求WWAN产品当地测试。
ENACOM in Argentina has accredited another lab, LENOR S.R.L. Laboratory, to test cellular interfaces on January 3, 2022. Since there are now three accredited laboratories in Argentina to test 2G/3G, and two laboratories in Argentina to locally test LTE, all Wireless Wide Area Network (WWAN) devices must be tested locally starting February 23, 2022.
India 印度
India TEC Phase III & IV 延期强制日期至2022年7月1日。
Department of Telecommunication , MTCTE ( Mandatory Testing and certification of Telecommunication Equipment has issued a new notification on amended rules for phase 3 and phase 4 products on 31/01/2022.
The main highlights are:
ILAC reports accepted with exception to safety and EMC. Need to check the annexure II of the document, as the product categories mentioned there, the technical parameters can have ILAC reports only if they are not border sharing countries with India.
ILAC reports will be allowed for technical parameters but need to check the annexure II of the document, as the product categories mentioned there, the technical parameters can have ILAC reports only if they are not border sharing countries with India.
India 印度
印度MTCTE预计将于 2023 年 1 月 1 日起针对第 5 阶段产品发布通知,包括:Server、Hypervisor、IP Terminal、5G RAN、5G Core unit、C- MSAAE、5G 用户设备和广播设备-混合机顶盒。
It is expected that the Department of Telecommunication , MTCTE ( Mandatory Testing and certification of Telecommunication Equipment) will issue notification from January 1st, 2023 for phase 5 products, including: Server, Hypervisor, IP Terminal, 5G RAN, 5G Core unit, C-MSAAE, 5G User Equipment, and Broadcasting Equipment- Hybrid Set-Top Box.
Monglolia 蒙古国
蒙古通讯传播监督委员会 (Communications Regulatory Commission- CRC) 于 2021 年 11 月 22 日针对第 37 号决议《短距离无线通信技术规范》之附录三公告部分修正,当中包含 Wi-Fi 产品的使用频段及输出功率限制值,同时也开放 Wi-Fi 6G 产品。
Communications Regulatory Commission- CRC issued No. 37 decision, revised output Power limitation for WiFi 2.4G/5G equipment, also open 5925 – 7125MHz to WiFi 6E.
5925-7125MHz, Output Power limitation is 100mW (EIRP), Indoor only, used for household AP.
Saudi Arabia 沙特阿拉伯
2022年1月1日,沙特阿拉伯通信和信息技术委员会 (CITC) 发布了《无线局域网条例》。该文件现已生效,取代“无线局域网 (WLAN/Wi-Fi) 使用规定”。无线局域网设备应在进口到沙特阿拉伯之前获得CITC的型式认证,并且需要符合相应的技术条件: 其中5925-7125 MHz作为Wi-Fi 6E频段。
The Communications and Information Technology Commission (CITC) of Saudi Arabia has published “WLAN Regulations” on January 1, 2022. This document is now in effect and replaces the document “Wireless Local Area Networks (WLAN/Wi-Fi) Usage Regulations.” 5925-7125 MHz (6 GHz) frequency band is opened for license-exempt use – WiFi 6E.
South Korea 韩国
2022 年 2 月 15 日,韩国贸易、工业和能源部 (MOTIE) 发布了 E-Standby 计划申请条例修正案。 该修正案主要从需要降低待机功率的产品中删除电脑和显示器,这两项产品将被指定为效率管理(MEPS)对象产品并进行管理。 该通知于 2022 年 2 月 15 日生效。当MEPS法规包括电脑、显示器的规则前,仍先按照之前的E-Standby法规进行评估,Korea Energy Agency预计会在3月份发布公文。
On 15 February 2022, the South Korean Ministry of Trade, Industry and Energy (MOTIE) issued an amendment to the E-Standby Program Application Regulation. The amendment primarily removes computers and monitors from Products Subject to Reduction of Standby Power. The said products would be designated and managed as Products Subject to Efficiency Management(MEPS). Relevant efficiency standards and labeling items etc would be provided in the MOTIE Notice on Energy Efficiency Labeling and Standards.
The Notice entered into force on 15 February 2022. However, the previous provisions may apply before the effective date of the MOTIE Notice on Energy Efficiency Labeling and Standards which reflects changes on computers and monitors. Korea Energy Agency estimate announce related official document at March.
South Korea 韩国
2021 年 2 月 8 日,韩国无线电研究机构 (RRA) 发布了对电磁兼容性标准的修订。 随着结合多媒体和通讯功能的智能电器数量的增加,本次修订将附件5规定的家用电器设备标准KS C
9814-1, KS C 9814-2电磁波抗扰度测试涵盖的电子产品范围重新分类,以反映最近的技术趋势。该通知自2022年2月7日起生效。
On 8 February 2021, the South Korean Radio Research Agency (RRA) issued an amendment to the Criteria for Electromagnetic Compatibility.
As the number of smart appliances combining multimedia and communication functions increases, this amendment is related to KS C 9814-1, KS C 9814-2 which are household electrical appliances, reclassifies the range of electronic products covered by electromagnetic wave immunity tests prescribed in Annex 5 as follows to reflect the recent technological trends:
The amendment also expands electromagnetic interference (EMI) measurement frequency bands from 30 MHz ~ 1 GHz to 30 MHz ~ 6 GHz, and further expands electromagnetic radiation immunity (EMS) test frequency bands by newly establishing the testing frequencies for the product range 3 to 5.
The Notice will enter into force on 7 February 2022.
China Taiwan 中国台湾
经济部标准检验局(BSMI)于2022年2月22日正式公告耳机自2024年1月1日起实施输入及国内产制商品检验要求,有两种合格评定程序供申请人选择,即产品认证注册(RPC)或型式逐批检验(TABI)。自公告日起,BSMI即可受理耳机申请型式认可或验证登录作业。
https://www.bsmi.gov.tw/wSite/public/Data/f1645585847882.pdf
on February 22, 2022, The Bureau of Standards, Metrology and Inspection (BSMI) announced that the requirements of Headphones are implemented from January 1, 2024. There are two procedures for applicants to choose: RPC Scheme(Modules II+III) or TABI Scheme. BSMI started to accept application from the announcement date.
https://www.bsmi.gov.tw/wSite/public/Data/f1645510399116.pdf
China Taiwan 中国台湾
经济部标准检验局(BSMI)于2022年2月22日正式公告「打印或复印设备等三十一项商品」与「电动削铅笔机等二十二项商品」之相关检验规定以最新版的电气安全规范、电磁兼容性和相关检验标准的CNS15598-1:2020 和 CNS15936:2016与国际标准接轨,以确保消费者的安全。
修正自公告日起实施,修正前检验标准自 2024年 1 月 1 日起停止适用。
https://www.bsmi.gov.tw/wSite/public/Data/f1645586012116.pdf
https://www.bsmi.gov.tw/wSite/public/Data/f1645586075866.pdf
On February 22, 2022, The Bureau of Standards, Metrology and Inspection (BSMI) announced the
amendments to the legal requirements for “printing or copying machines and 30 other commodities “&“Electric Pencil Sharpeners and 21 Other Commodities“ with immediate effect. The revised inspection standards are the latest version of the electrical safety specifications, electromagnetic compatibility and related inspection standards: CNS15598-1: 2020 and CNS15936: 2016, to bring our regulations into line with the international standards to ensure consumers’ safety.
Taiwan Standard |
Harmonized IEC standard |
CNS 15598-1:2020 |
IEC 62368-1:2018 3rd edition |
CNS 15936:2016 |
CISPR32: 2015 2nd edition |
The current inspection standards will become invalid from 1 January 2024.
https://www.bsmi.gov.tw/wSite/public/Data/f1645511043398.pdf
https://www.bsmi.gov.tw/wSite/public/Data/f1645511658884.pdf
China Taiwan 中国台湾
经济部标准检验局(BSMI)于2022年2月23日提议无线充电器商品之相关检验规定修正草案。
修正前: 验证登录
修正后: 型式认可逐批检验或验证登录
预计自2022年8月1日起实施
https://www.bsmi.gov.tw/wSite/public/Data/f1645687624034.pdf
The Bureau of Standards, Metrology and Inspection (BSMI) proposed on February 23, 2022 for amendments to the Legal Inspection Requirements for Wireless Chargers.
Before: Registration of Product Certification (RPC)
After: Registration of Product Certification (RPC) or Type-Approved Batch Inspection (TABI)
Proposed date of implementation: 1 August 2022
https://www.bsmi.gov.tw/wSite/public/Data/f1645687624034.pdf
家用电器 House Appliances
Brazil 巴西
2022 年 1 月 20 日,巴西国家计量、标准化和工业质量研究所 (INMETRO/CONMETRO) 发布了第 8 号协议,以批准南方共同市场关于燃气器具最低安全和能效要求的技术法规以及家用燃气灶和烤箱的合格评定要求。本协议于 2022 年 2 月 1 日生效,并废除第 400/2012 号和第 496/2013 号协议。
On 20 January 2022, the Brazil National Institute of Metrology, Standardization and Industrial Quality (INMETRO/CONMETRO) published Portaria No. 8 to approve Mercosur Technical Regulation on Minimum Safety and Energy Efficiency Requirements for Gas Appliances along with requirements for conformity assessment of domestic gas stoves and ovens.
The Portaria applies to gas cookers and ovens for domestic use, including those with electric grills, electric grills and induction hobs as accessories, of the following types:
This Portaria will enter into force on 01 February 2022 and will repeal Portarias No. 400/2012 and No. 496/2013.
Chile 智利
2021 年 12 月 2 日,智利电力和燃料监管局 (SEC) 发布了第 9708 号决议,批准第 1/19:2021 号议定书。本议定书根据标准 IEC60335-2-30: 2009 + AMD1: 2016 + AMD2: 2021 的适用范围和领域,更新了家用取暖器的认证程序,并将于 2022 年 11 月 30 日起开始实施,原依据第 1/19:2015 号决议取得认证的批次产品或在该国售完即止;第 9708 号决议于 2021 年 12 月 2 日生效。
On December 2, 2021, the Chilean Superintendency of Electricity and Fuels (SEC) published Resolution No. 9708 approving Protocol PE No. 1/19:2021. This Protocol establishes the procedure for certification of domestic space heaters, in accordance with the scope and field of application of Standard IEC60335-2-30: 2009 + AMD1: 2016 + AMD2: 2021.
Per Article 2 Resolution No. 9708, manufacturers and importers shall have their products certified in accordance with PE No. 1/19:2021 from 30 November 2022. Batches of products that were certified in accordance with Protocol EP No 1/19:2015 before the date of application of Protocol PE No. 1/19:2021 may be marketed in the country while supplies last. Manufacturers are producers, however, are encouraged to use the new protocol immediately.
The Certification Body will reject the product in the event that these instructions are not followed.
Resolution No. 9708 came into force on December 2, 2021.
Protocol PE No. 1/19: 2021 will be applicable from 30 November 2022.
Chile 智利
2021 年 12 月 2 日,智利电力和燃料监管局 (SEC) 发布了第 9709 号决议,批准第 1/11:2021 号议定书。 本议定书根据 IEC 60335-2-14:2016+AMD1:2019 CSV 的适用范围和领域,更新了家用和类似用途厨房机器的认证程序。并将于 2023 年 3 月 30 日起开始实施,原依据第 1/11:2012号决议取得认证的批次产品或在该国售完即止;第 9709 号决议于 2021 年 12 月 2 日生效。
On December 2, 2021, the Chilean Superintendency of Electricity and Fuels (SEC) published Resolution No. 9709 approving Protocol PE No. 1/11:2021. This Protocol establishes the certification procedure (Chapter III, incl. testing) for kitchen machines for domestic use and similar purposes in accordance with the scope and field of application of IEC 60335-2-14:2016+AMD1:2019 CSV.
Manufacturers and importers shall have their products certified in accordance with PE No. 1/11:2021 from 30 March 2023. Batches of products that were certified in accordance with Protocol PE No. 1/11:2012 before the date of application of PE No. 1/11:2021 may be marketed in the country while supplies last.
The Resolution came into force on December 2, 2021.
The date of application of Protocol PE No. 1/11:2021 is 30 March 2023.
Chile 智利
智利电力和燃料监管局 (SEC) 于 2021 年 12 月 2 日颁布了 2021 年第 9710 号决议,批准关于某些家用液体加热设备的安全测试和认证的第 1/12:2021 号协议。该协议描述了获得认证的要求和方法,并规定范围内的产品必须根据 IEC 60335-2:2018-11 进行认证。协议PE No. 1/12:2021 自 2022 年 11 月 30 日起适用,并废除协议 PE No. 1/12:2014。
The Chilean Superintendency of Electricity and Fuels (SEC) enacted Resolution No. 9710 of 2021 approving Protocol PE No. 1/12:2021 on 2 December 2021, about safety testing and certification of certain household liquid heating appliances.
The followings are examples of products in scope:
The Protocol describes the requirements and methodology for achieving certification and provides that products in scope must be certified in accordance with IEC 60335-2:2018-11.
Manufacturers and importers shall have their products certified in accordance with Protocol PE No. 1/12:2021 from 30 November 2022. Batches of products that were certified in accordance with Protocol PE No. 1/12:2014 before the date of application of PE No. 1/12:2021 may be marketed in the country while supplies last.
Protocol PE No. 1/12:2021 applies from 30 November 2022 and repeals Protocol PE No. 1/12:2014.
Singapore 新加坡
新加坡企业发展局 (ESG) 于2月7日发布公告:消费品安全办公室 (CPSO) 将对《消费者保护 (安全要求) 条例》(CPSR) 中饮水机的检测与认证要求进行澄清。其中,
(1)饮水机检测与认证要求:
(2) 饮水机的注册:
This circular is to provide clarification regarding the testing and certification requirements for water dispensers under the Consumer Protection (Safety Requirements) Regulations (CPSR).
III. IEC Technical Committee 61 (TC 61) has clarified in July 2021 that ‘water boiling’ as mentioned in DSH 579 refers to water reaching 100 °C at 1 atmosphere
The Consumer Product Safety Office (CPSO) safeguards consumer safety by ensuring consumer products supplied in Singapore are safe for use and comply with applicable safety standards. The CPSO is an office under Enterprise Singapore. Visit www.consumerproductsafety.gov.sg for more information.
灯具 / LED Luminaiaries / LED
Chile 智利
2021 年 12 月 10 日第 9874 号决议批准了第 5/19:2021 号议定书,更新了适用于泛光灯的安全认证程序的标准要求(IEC 60598-2-5: 2015-08),并计划2023 年 2 月 28 日为第 5/19:2021 号决议的开始实施日期。
Protocol No. 5/19:2021, approved by Resolution No. 9874 on 10 December 2021, sets out the requirements for the safety certification procedure applicable to floodlights.
The Protocol applies to floodlights on supply voltages not exceeding 1 000 V to be used for projection lighting, when the light is directed by reflection and/or refraction, to be used with electrical light sources such as incandescent, fluorescent, discharge lamps, LED, Induction or other technologies, according to the scope and field of application of the Standards IEC 60598-2-5: 2015-08.
Protocol No. 5/19:2021 does not apply to the following products:
Resolution No. 9874 was published on 10 December 2021, approving an application date for Protocol No. 5/19:2021 of 28 February 2023.
Note: consignments of products whose monitoring was carried out per Protocol PE No. 5/19 of 2013, before the date of application of protocol PE No. 5/19: 2021, may be marketed in the country while supplies last. Manufacturers and importers interested in using protocol PE No. 5/19:2021 before its entry into application may do so when there are Certification Bodies authorized for such purposes.
Thailand 泰国
本公告由泰国工业部于 2021 年 1 月 26 日发布,制定了关于管状荧光灯灯座和启动器灯座的工业标准 TIS 344-2562。 该标准规定了管状荧光灯灯座和启动器灯座的技术和尺寸要求,以及用于确定灯座中的灯和启动器在启动器座中的安全性和适合性的测试方法。该标准自 2022 年 1 月 28 日起强制实施。
Issued on 26 January 2021 by the Thai Ministry of Industry, this Announcement establishes Industrial Standard TIS 344-2562 on Lampholders for Tubular Fluorescent Lamps and Starterholders, in accordance with the Industrial Product Standards Act.
The Standard sets out the technical and dimensional requirements for lampholders for tubular fluorescent lamps and for starterholders, and the testing methods to be used in determining the safety and the fit of the lamps in the lampholders and the starters in the starterholders.
The standard consists of scope, definitions, general requirements, testing, marking, dust resistance, moisture and insulation resistance, electrical strength, resistance to heat and fire, etc.
The standard will be of mandatory application with effect from 28 January 2022.
能源效率要求 Energy Efficiency Requirements
澳大利亚
65 千瓦 (kW) 以上的空调引入能效要求的日期已推迟六个月至 2022 年 10 月 1 日。
从 2022 年 10 月 1 日起,供应或进口65kW以上空调的注册人必须通过能效评级产品注册系统向 GEMS 监管机构注册其所有产品型号。
Update to the introduction of Air Conditioner Determination – above 65 kW
The date for the introduction of energy efficiency requirements for air conditioners above 65 kilowatt (kW) has been postponed by six months to 1 October 2022.
From 1 October 2022, registrants who supply or import air conditioners covered by the new Determination must register all models of their products with the GEMS Regulator through the Energy Rating Product Registration System.
EAEU 欧亚经济联盟
2022 年 2 月 11 日,EAEC 发布第 23 号决定,关于批准进口到 EAEU 并需符合TR EAEU 048/2019的能源消耗设备清单。该清单包括 18 组产品,每组都标明了 EAEU HS code来划分需要申请强制性符合性证书或强制性符合性声明。
第 23 号决定于 2022 年 3 月 13 日生效;EAEU TR 048/2019 于 2022 年 9 月 1 日生效。
https://docs.cntd.ru/document/728138229
On 11 February 2022, the Eurasian Economic Commission published Decision No. 23 to approve a list of products in respect of which the customs declaration is accompanied by the conformity assessment document.
Annexed to the Decision is a list of products in respect of which the submission of a customs declaration must be accompanied by a document attesting conformity assessment with the requirements of the technical regulations of the Eurasian Economic Union on energy efficiency for electrical and electronic equipment (EAEU TR 048/2019).
The list includes 18 items, the EAEU HS code is indicated for each group.
Two types of conformity assessment are possible for the products in the list: mandatory certification and mandatory declaration of conformity, depending on the products groups and the HS code.
The Decision shall enter into force on 13 March 2022. EAEU TR 048/2019 comes into force on Sep. 1st, 2022.
https://docs.cntd.ru/document/728138229
其他 / 多主题产品 Others / Products with Multiple Subjects
EAEU 欧亚经济联盟
2021 年 12 月 23 日,俄罗斯联邦政府发布了第 2425 号决议,批准新清单: 强制认证和强制声明产品统一列表 (只适用于俄罗斯)。产品若同时列于新清单与EAEU技术法规 (Technical Regulation) 中,以EAEU技术法规 (Technical Regulation)为主。
新的强制认证产品列表包括 26 个产品组,新的强制声明产品列表包括 67 个产品组。这些列表中包含的产品由海关税则码来判别。
第 2425 号决议中包含的产品列表中,详细说明了对这些产品的要求、规则和测试方法,以及选择样品的必要规则。
第 2425 号决议将于 2022 年 9 月 1 日生效,但首次列入清单的强制性合格评定产品除外,其生效日期定为 2023 年 9 月 1 日,使产品制造商和供货商有机会为实施具有约束力的要求做准备,并也让认证机构和测试实验室有时间获得适当的稽核认可。
俄罗斯联邦政府 2009 年 12 月 1 日第 982 号决议“关于批准强制性认证的产品单一列表和以声明的形式确认符合性的产品单一列表”有效期至 2022 年 9 月 1 日,之后将被第 2425 号决议取代。之前颁发的产品符合性证书和符合性声明可用到证书或声明上的到期日,但最晚不超过 2025 年 9 月 1 日。
第 2425 号决议有效期至 2028 年 9 月 1 日。
https://docs.cntd.ru/document/727708039
The Government of the Russian Federation has approved new lists: the Unified List of Products Subject to Mandatory EAC Certification and to EAC Declaration.
The new list of products subject to EAC certification includes 26 product groups, including oil products, pipes and fittings, cement, radiators, civilian and service arms and cartridges, and mining equipment. In turn, 67 product groups are subject to EAC declaration, including in particular crockery, mineral and phosphate fertilizers, household chemicals and paints and varnishes, batteries and rechargeable batteries and disinfectants.
Information is added to the lists of products contained in Resolution No. 2425, specifying requirements for these products, rules and methods of tests, as well as the necessary rules for selecting samples. In addition, the products contained in these lists are identified by the customs tariff number.
Resolution No. 2425 will come into force on September 1, 2022, except for the requirements for objects of mandatory conformity assessment, which were included in the lists for the first time, for which the effective date is set for September 1, 2023. This gives product manufacturers and suppliers the opportunity to prepare for the implementation of binding requirements, and certification bodies and testing laboratories to receive appropriate accreditation for working with new items of conformity assessment. Resolution No. 2425 is valid until September 1, 2028.
The Resolution of the Government of the Russian Federation of December 1, 2009 No. 982 “On approval of a single list of products subject to mandatory EAC certification and a single list of products whose Conformity is confirmed in the form of an EAC declaration” is valid until September 1st, 2022. Previously issued certificates of conformity and declarations of conformity for products are valid until the expiry date specified therein, but no longer than September 1st, 2025.
https://docs.cntd.ru/document/727708039
Serbia 塞尔维亚
2022 年 1 月 13 日,塞尔维亚政府发布本条例,规定在产品上粘贴塞尔维亚合格标志的条件、外观和方式。该法规第 3 条规定,塞尔维亚合格标志是确认产品符合适用于其特定技术要求的唯一标志。然而,本条款将在 ACAA (工业产品合格评定和验收协议) 与欧盟生效之日起失效,或者,如果本协议未缔结,则自塞尔维亚共和国加入欧盟起失效。此后,CE 标志将成为确认产品符合相关欧盟法规的唯一标志。
本条例于 2021 年 1 月 14 日生效,自 2022 年 5 月 1 日起实施。
On 13 January 2022, the Serbian government issued this Regulation concerning the conditions, appearance, and manner of affixing the Serbian conformity mark to products. The Regulation was issued pursuant to Article 14(5) of the Law on Technical Requirements for Products and Conformity Assessment.
Article 3 of the Regulation states that the Serbian mark of conformity is the only mark that confirms the compliance of a product with the specific technical requirements applicable to it. This provision will however cease to be valid on the date of entry into force of the ACAA (Agreement on Conformity Assessment and Acceptance of industrial products) with the EU or, if this agreement is not concluded, from the date of entry into force on the accession of the Republic of Serbia to the European Union. Thereafter, the CE mark will be the only mark that confirms a product is compliant with the relevant EU regulation, upon which Serbia’s requirements are based.
Article 6 stipulates that the mark of conformity must be affixed in a way that is visible, legible and indelible, and to a place that is easily accessible for inspection. If it is not possible to place the mark on the product itself, then it can be printed on the packaging or, failing that, printed on the product documents.
Per Article 11 the Serbian mark of conformity can be placed on imported products based on a decision from the competent authority, or on the basis of a certificate of conformity that is issued by an approved body.
This Regulation entered into force on 14 January 2021, and applies from 1 May 2022.
Ukraine 乌克兰
考虑到乌克兰最近的新闻和局势,所有提交给乌克兰的案件目前都被搁置。目前认证机构无限期停工。
All certification projects submitted to Ukraine CAB are currently put on the hold, taking into account recent news and situation in Ukraine.
At the moment the certification bodies are off work for indefinite time.
推荐文章
关注我们
4001183833 / 8009993668
Service-gc@tuv.com
www.tuv.com
德国莱茵TÜV是一家国际领先的技术服务供应商。在全球近60个国家和地区设有500多个分支机构,拥有超过20,000名员工,服务涵盖工业服务与信息安全,交通服务,产品服务,管理体系服务和莱茵学院与生命关怀。自1872年成立以来,我们一直为解决人类、环境和科技互动过程中出现的挑战,提供安全的、可持续的解决方案。作为一个独立、公正和专业的机构,我们长期致力于营造一个同时符合人类和环境需要的美好未来。
热门分享