- RF and SAR
- Optical and Laser
- Annex 1: Mobile devices standards
- Annex 2: Mobile network radio base stations standards
- Annex 3: Standards for PMR
- Annex 4: Broadcast equipment standards
- Annex 5: License-exempt equipment standards
- Annex 6: Analogue telecommunications line equipment standards
- Annex 7: satellite communications equipment standards
- Annex 8: miscellaneous equipment standards
- Added new frequencies
- Removed usage of the frequencies
- Removed wireless access device schedule, and change the total schedule to twenty-nine schedule
- 临时批准 (目前适用): 从2020年11月6日到2021年6月29日
- 完全批准: 2021年6月30日之后
- From November 6, 2020, to June 29, 2021.
- The request for approval shall be submitted with a declaration of VoLTE support and that the function is enabled in the device.
- VoLTE test reports will also be accepted instead of a declaration after February 15, 2021.
- After 30 June 2021.
- All new applications shall be submitted with a VoLTE test report (mandatory) and the VoLTE declaration is no longer accepted.
- The VoLTE test reports must be tested by a laboratory accredited under IR.92 or TS 34.229-1 or equivalent standards
- For applications submitted during the interim period above by declaration, they shall be updated by submitting the VoLTE test report by 30 June 2021 to continue CoC’s validity.
- Manufacturers are no longer permitted to affix the SM conformity mark and the CE marking to the same radio equipment.
- The affixing of the conformity mark is performed during the manufacturing process. Therefore, radio equipment manufacturers can decide to apply either the SM mark or the CE mark only on equipment produced after February 22, 2021.
- The products and stocks of products that were previously approved by the authority and manufactured and labeled prior to February 22, 2021, are not required to comply with this provision and shall be allowed to be placed on the market of the Republic of Moldova even if both conformity marks are placed on the same equipment.
- Immunity test for household electrical equipment: KS C 9814-2:2020
- Interference prevention test of household electrical equipment: KS C 9814-1:2020
- Common EMC test for radio equipment: KS X 3124:2020
- EMC test for specific low power wireless devices for wireless data communication systems: KS X 3126:2020
- EMC test for specific low power wireless devices: KS X 3125:2020
- Electromagnetic interference prevention test for multimedia equipment: KS C 9832:2019
- Electromagnetic wave immunity test for multimedia devices: KS C 9835:2019
- EMC test method for wireless devices for vehicle wireless devices and electrical and electronic components mounted on vehicles: KS C 9995:2021
- EMC test for automobiles and internal combustion engines, etc: KS C 9990:2017
- Interference prevention test for lighting equipment: KS C 9815:2019
- Immunity test for lighting equipment: KS C 9547:2020
- EMC test method for electric bicycles: KS C 9994:2021
- Immunity test for medical devices: KS C IEC 60601-1-2:201.
- vertical cooler with one or more doors of minimum capacity 25L
- horizontal coolers of minimum capacity 50L
- horizontal freezers (including medical) of minimum capacity 50L
- vertical freezers of minimum capacity 50L
- closed cabinets of minimum capacity 100L
- ice pack keepers of minimum capacity 100L
- cooling or freezing rooms
- coolers with drink dispensers
- doorless coolers
- combined/2in1 cooler/freezers
- remote refrigeration equipment, wine coolers, wine cellars, water coolers, water dispensers, and ice-making machines.
- decorative and artistic lighting and architectural lighting
- illumination and illumination of advertising structures
- emergency and evacuation lighting
- special-purpose lighting and military equipment.
- As the Electrical Supply Track Systems for Luminaires are added to electrical appliances subject to safety assurance, the draft brings changes to the Annexes as follows:
- Adding the said products to the detailed items of lighting equipment subject to safety assurance in Annex 2 (supplements the existing list of chain lighting fixtures, rechargeable portable lights, floodlight luminaires, and halogen luminaires)
- Adding the model classification and its detailed criteria of the said products to Annex 10
- Adding a list of parts subject to safety control of the said products to Annex 20
- Adding safety standard KC 60570 for the products to Annex 25.
- In the transition period, the evaluation shall be performed based on the old or new version of the standard voluntarily, while after the implementation of the new version of the standard, the evaluation shall be performed in accordance with the new version of the standard.
- For the products that have completed the self-declaration in accordance with the old version of the standard, the new version of the standard self-declaration change should be completed within one year. Products that have been shipped, put on the market, and are no longer produced before the implementation of the new version of the standard do not need to carry out the new version of the standard self-declaration.
资讯 / 电信 ITE / Telecom
On 2020-01-20, the Algerian Republic published the JOURNAL OFFICIEL DE LA REPUBLIQUE ALGERIENNE N°05
The new list of Characteristics of short-range devices used in the establishment of private internal radio networks has been published.
The maximum allowed Output Power / maximum magnetic field level has been defined for several frequency bands from 9 kHz – 246 GHz considering different applications like inductive, RFID, medical, general ISM applications, and Radars.
Now the 77 GHz Band with a limitation of 1W maximum output power is possible.
ANATEL published on Jan 5th, 2020 the new Act 77. This act approves the Cyber Security Requirements for Telecommunications Equipment. This new Act will become in force after 180 days of its publication.
Here are some of the main points:
This act is applicable to all terminal devices with connection to internet and telecommunications network infrastructure equipment.
According to item 4.1, when requesting the approval of devices under the scope of this act, ANATEL will request a Declaration Letter from the applicant with the following content:
a)indicating that the product was developed in compliance with the principle of security by design
b)relating to which requirements of this document the equipment and its supplier meet at that moment; and
c)Recognizing that they are aware that cybersecurity requirements are subject to updates, including regulatory and administrative ones, in line with technological development, with the emergence of new threats or vulnerabilities.
According to item 4.2, when ANATEL implements the Market Surveillance program, they can assess whether the product and its supplier maintain compliance with the requirements of this Act.
Items 5 and 6 of Act 77, describes the specific requirements for Cyber Security, such as:
c)Installation and Operation
d)Access to the device configuration
2021年1月20日，ANATEL宣布5G NR技术评估相关测试的部分 – 截至2021年3月31日之前，仍可以接受国外测试报告。
On January 20, 2021, the Agência Nacional De Telecomunicações (ANATEL) in Brazil informed through an official letter that the deadline for providing complimentary tests reports related to the evaluation of 5G NR technology has been extended (from January 31) to March 31, 2021.
There are currently two laboratories in Brazil that can test for 5G NR technology. However, manufacturers have the option to provide test reports issued by foreign test labs to support the homologation of their 5G NR devices before March 31, 2021.
Two more local laboratories are expected to be available by the end of March 2021. Then, after 31st March 2021, it is expected that local testing for 5G NR will be mandatory in Brazil.
2020年12月21日智利SEC发布法规N°33811，推出SEC 协议PE N°8/10:2020。PE N°8/10:2020主要是要用IEC 62368-1:2014 或者 IEC 62368-1:2018 替换IEC 60950-1。涉及的产品有电脑 (笔记本和台式机)，平板电脑和手机的外置适配器。
现有的协议PE N°8/08:2016 (手机充电器) 和PE N°8/9:2019 (笔记本和台式机电脑外置适配器) 依然有效，推测会给1-2年的过渡期过度到PE N°8/10:2020。
SEC has issued the SEC Resolution N°33811 launching the new SEC Protocol PE N°8/10:2020 for external power supplies for computers (laptops and desktops), tablets, and mobile phones.
This SEC protocol replaces the use of IEC 60950-1 by IEC 62368-1:2014 or IEC 62368-1:2018.
According to SEC, the current SEC Protocols PE N°8/08:2016 (battery charger for mobile phones) and PE N°8/9:2019 (external power supplies for computers (Laptops and Desktops)) will be still valid after the new SEC Protocol PE N°8/10:2020 enters into force. It is estimated that there will be a grace period (maybe 1 or 2 years) until the manufacturers and importers change to the new SEC Protocol PE N°8/10:2020.
根据俄罗斯联邦经济发展部的法令 (2020年7月31日第478号、2020年12月30日第877号、2020年11月18日第1856号)，俄罗斯境外的企业申请EAC CoC 或者 DoC 时，需提供全球位置编码Global Location Number (GLN) 和/或 全球交易品项识别码Global Trade Item Number (GTIN)。GLN号码的强制日期如下:
EAC DoC: July 01, 2021
EAC CoC: August 01, 2021
According to the Russian Federation Government Regulations (№478 dated July 31, 2020, №877 dated December 30, 2020, and №1856 dated November 18, 2020), when enterprises outside Russia apply for EAC CoC or DoC, the Global Location Number (GLN) and/or Global Trade Item Number (GTIN) must be provided. The mandatory dates for GLN numbers are as follows:
EAC DoC: July 01, 2021
EAC CoC: August 01, 2021
Although the GTIN number is not mandatory, if the GTIN number of the product is shown in the label or any cargo shipping documents, the number should be provided in advance when applying for DoC or CoC so that the Certification Body or local agent can register the number in FGIS database.
Some products, such as cameras, perfume, and toilet water, shoes, some types of clothing, etc., have special labeling requirements. For these products, GTIN numbers are also mandatory.
On 2 February 2021, the Indian Department of Telecommunications issued a Circular Regarding misuse of the Approval Certificate issued by TEC as “Proof of Manufacturer”.
It has come to the notice of TEC that the Approval Certificate may be misused as a “Proof of Manufacturer”.
In this regard, it is clarified that:
a) Approval Certificates issued by TEC are not proof of Manufacturing location/capabilities, ownership details, claim regarding local content of the product, etc., and are issued subject to Terms and Conditions mentioned overleaf in the Certificate.
b) In all future certificates, the type of Applicant (Trader/Manufacturer) shall also be mentioned to distinguish the trader from the manufacturer clearly.
The above annotation is applied to the existing valid and future Certificates to be issued.
However, if any such case is noticed/established regarding misuse of the Certificate, TEC reserves the right to cancel/suspend the Certificate.
SDPPI文件评估流程延长至2021年7月22日。SDPPI正式发布了新公告 (KEPDIRJEN 11/2021) ，延长对HKT和Non-HKT产品的文件评估，并增加HKT和Non-HKT产品报告的认可实验室。 TÜV莱茵拥有相关HKT / Non-HKT产品的完整范围。
Telecommunications ministry (SDPPI) has released an official announcement regarding the extension of the telecommunications equipment certification process through document evaluation.
Previously telecommunications ministry (SDPPI) regulated the document evaluation process in Kepdirjen 124/2020 which ended on January 23rd, 2021. In that regulation, the list of accredited labs for HKT products is 16 labs and for non-HKT products is 72 labs.
Based on that expired regulation, SDPPI decides to extend the document evaluation process for HKT and Non-HKT products. SDPPI has released the Kepdirjen 11/2021, in this new regulation, SDPPI sets 39 accredited labs for HKT products and 126 accredited labs for Non-HKT products.
Thus, the test report from the attached list of labs can be accepted by SDPPI to process certification. This regulation is valid for 6 months from the stipulation date.
2021年1月31日，科威特通信和信息技术管理局 (CITRA) 发布指导文件，其中包括与连接到公共电信网络的ICT设备相关的各种技术标准的列表。CITRA正在建立型式认证实验室。完成后，将批准并发布新的型式认证流程。
On 31 January 2021, the Kuwait Communication and Information Technology Regulatory Authority (CITRA) issued this guidance document that includes a list of various technical standards related to ICT equipment connected to the public telecommunication network.
The Government of Kuwait has established a type approval process for all ICT equipment used within the country. The standards applied in Kuwait include standards that are also used for European ICT equipment and commonly applied across the GCC. Hence, the Current ETSI standards as used under the new RED type approval process in Europe are considered technical standards applied in Kuwait. CITRA is in the process of establishing a type approval lab. Once done, a new type of approval process will be approved and published.
Section 3.0 includes a list of safety requirements standards and they are divided into the following categories:
The annexes to this guidance document include the following standards:
2021年1月7日，MCMC / SIRIM宣布对在3GPP Band 20 (800MHz) 运行的用户设备 (UE) 进行认证。UE必须遵守标准ETSI EN 301 908-13 (通过提交测试报告来证明)。
On January 7, 2021, MCMC/SIRIM announced that User Equipment (UE) operating in the 3GPP Band 20 (800MHz) shall now be certified.
The UE must comply with the standard ETSI EN 301 908-13 (proven through submission of test report). All other scopes of products must comply with the related MCMC Technical Code (e.g. 2G, LTE, WiFi, etc.) as stated in the Certification Requirement document.
2020年12月14日，马来西亚通讯与多媒体委员会 (MCMC) 发布了关于新产品等级分配的2020年1号文件，该文件取代了2019年1号文件。新产品等级分配涵盖了从类别1到类别29的所有设备，产品范围涵盖从SRD、对讲机到蜂窝移动接入设备。
Malaysia MCMC announced the latest Class Assignment No. 1 – 2020.
Class Assignment No.1 2019 will be canceled and replaced by Class Assignment No.1 – 2020.
The New Class Assignment is commencing on November 9th, 2020.
There are few minor changes in Class Assignments No. 1 – 2019 which will be replaced by Class Assignment No. 1 – 2020.
2021年1月14日，马来西亚标准与工业研究院管理局 (SIRIM) 宣布符合VoLTE功能的产品的要求。支持VoLTE的4G设备的所有新申请都需要显示对此功能的符合性。SIRIM定义了两个实施阶段:
On January 14, 2021, the Standard and Industrial Research Institute Authority (SIRIM) of Malaysia announced the requirements for compliance of VoLTE capable products.
From now on all new applications for 4G devices that support VoLTE require showing compliance with this feature. To do this, SIRIM defined two implementation phases:
Interim Approval (current):
According to the new regulation TR34/2019, which came into force in February 2021, the application of both CE and SM marks on the same product will not be permitted anymore.
TR34/2019 defines the following:
The Certification authority in Moldova recommends that manufacturers who have not begun Type Approval applications or have only partially completed the application process, start to remove the SM mark if the radio equipment is already labeled with the CE mark.
South Korea 韩国
2021年2月8日，韩国无线电研究局 (RRA) 发布电磁兼容性标准的修正案。 随着结合了多媒体和通信功能的智能设备的数量增加，此修订对附件5中规定的电磁波抗扰度测试涵盖的电子产品范围进行了重新分类，以反映最近的技术趋势。该通知将于2022年2月7日生效。
On 8 February 2021, the South Korean Radio Research Agency (RRA) issued an amendment to the Criteria for Electromagnetic Compatibility.
As the number of smart appliances combining multimedia and communication functions increases, this amendment reclassifies the range of electronic products covered by electromagnetic wave immunity tests prescribed in Annex 5 as follows to reflect the recent technological trends:
1: Devices without electrical control circuit
2: Equipment’s with an internal clock frequency of 15 MHz or less
3: Battery devices that are not included in the range of product 1
4: Products with internal clock frequency exceeding 15MHz and below 200MHz
5: Devices with internal clock frequency exceeding 200MHz.
The amendment also expands electromagnetic interference (EMI) measurement frequency bands from 30 MHz ~ 1 GHz to 30 MHz ~ 6 GHz and further expands electromagnetic radiation immunity (EMS) test frequency bands by newly establishing the testing frequencies for the product range 3 to 5.
The Notice will enter into force on 7 February 2022.
South Korea 韩国
2021年2月8日，韩国无线电研究局 (RRA) 发布电磁兼容性 (EMC) 合格评定测试方法的修正案。 发布该修正案是为了更改某些KN测试方法，并引入了新的国家标准操作系统，这些方法在《 EMC国家标准符合性评估测试方法通告》的附件中。该通知将于2021年5月7日生效。
On 8 February 2021, the South Korean Radio Research Agency (RRA) issued an amendment to the Electromagnetic Compatibility (EMC) Test Methods for Conformity Assessment.
The amendment was issued to change certain KN test methods, which are in the annexes of the Notice on EMC Test Methods for Conformity Assessment to the National Standards (KS), with the introduction of the new national standard operating system.
Applicable devices and changed KS standards include:
The amendment further changes test methods related to measuring instruments for electromagnetic interference and immunity, etc.
The Notice will enter into force on 7 May 2021.
South Korea 韩国
2021年2月1日，韩国技术与标准局 (KATS) 发布《电器和消费品安全控制法案》的修订草案。 该草案将添加有关非面对面抽样和工厂检查标准的新附件30，以便在自然灾害或大流行性疾病期间，对现场工厂检查引入非面对面评估和KC安全认证审核方法。
On 1 February 2021, the South Korean Agency for Technology and Standards (KATS) issued a draft amendment to the Operation Bulletin of Electrical Appliances and Consumer Products Safety Control Act.
The draft would add a new Annex 30 on non-face-to-face sampling and factory inspection standards in order to introduce non-face-to-face evaluation and audit methods for KC safety certification, in cases when the on-site factory inspection is not possible due to natural disasters or pandemic disease.
Also, the draft would add notebook PCs to the list of products for which electronic-labeling can be made as per Article 59.
South Korea 韩国
2021年2月1日，韩国贸易，工业和能源部 (MOTIE) 发布《电器和消费品安全控制法实施规则》修正案草案，该草案将把音频处理器和视频处理器的安全管理级别从受安全保证的产品变为供货商的合格保证。有兴趣的单位可在2021年3月15日之前在线提交评论。
On 1 February 2021, the South Korean Ministry of Trade, Industry, and Energy (MOTIE) issued a draft amendment to the Electrical Appliances and Consumer Products Safety Control Act Enforcement Rules to reduce the corporate burden by reviewing the level of risk for products subject to safety management.
The draft would changes the level of safety management for audio processors and video processors from products subject to safety assurance to the supplier’s assurance of conformity.
The draft further improves the model classification by EEE subject to safety control, by changing the location of items and deleting unnecessary model categories, in Annex 1.
Interested parties are required to submit their comments online before 15 March 2021.
泰国工业部于2021年1月21日发布并立即实施关于音视频，信息和通信技术设备之安全要求的工业标准TIS 62368 (1)-2564，该标准基于IEC 62368-1发行。
This Announcement issued with immediate effect on 21 January 2021 by the Thai Ministry of Industry, establishes Industrial Standard TIS 62368 (1) – 2564 on Audio/video, Information and Communication Technology Equipment – Part 1: Safety Requirements, in accordance with the Industrial Product Standards Act.
The Standard was issued based on IEC 62368-1 and provides for safety characteristics of electrical and electronic equipment within the field of audio, video, information and communication technology, and business and office machines with a rated voltage not exceeding 600 V. The standard does not include requirements for performance or functional characteristics of the equipment.
It also classifies energy sources, prescribes safeguards against those energy sources, and provides guidance on the application of, and requirements for, those safeguards.
Lastly, the Standard consists of general provisions, principles of product safety standards, scope, reference documents, definitions, general requirements, injury caused by electricity, fire caused by electricity, and injuries caused by hazardous substances, etc.
家用电器 Household Appliances
Ministry of Commerce and Industry published the official “Refrigeration Appliances (Quality Control) Order, 2020″ ”which will be forced into effect from 2022/01/01.
Air Conditioner and its related Parts, Hermetic Compressor and Temperature Sensing Controls (Quality Control) Second Amendment Order, 2020.
There have been some changes in the quality control order which postpone the implementation date from 2020/06/01 to 2022/01/01.
Temperature Sensing control devices, which were part of the initial regulation will stand omitted from the regulation when it is implemented after 2022/01/01.
New regulation update No. 58 years 2020 regarding the SNI mandatory standards for Kitchen machines and Heating liquid appliances. This regulation is issued under the Ministry of Industry authorities and will be officially implemented from December 22nd, 2021.
Detail timeline regarding this regulation:
Regulation Issued: December 23rd, 2020
SNI mandatory applied: December 22nd, 2021 (Issued date + 12 months)
Grace period 2 years: December 22nd, 2022 (Applied date + 2 years)
The grace period for products that already exist without the SNI mark in the market is 2 (two) years after the issuance date of this regulation. It means, products that are already produced (without the SNI mark) still can be sold in the market until December 22nd, 2022.
The certification scheme for audio-video is type 5 (the factory needs to be audited and local testing is required). The products covered in the scope of this regulation are as follows with the detailed HS Code No.:
On 22 January 2020 the Panamanian Ministry of Trade and Industry published Resolution No 04/2021 to amend Resolution No. 31/2018 on Approving Technical Regulation DGNTI-COPANIT 105:2017 on Energy Efficiency and Labelling Requirements of Refrigerators and Freezers.
This Resolution amends Point 2 (Scope) of Technical Regulation DGNTI-COPANIT 105:2017 in order to provide a precise indication of the appliances that are excluded from the scope of the requirements:
This Resolution entered into force on 22 January 2021.
South Korea 韩国
2021年1月12日，韩国贸易，工业和能源部 (MOTIE) 发布《电器和消费品安全控制法实施规则》的修订草案，主要是将制冰机的安全控制级别从“需要安全保证的产品”更改为“需要供货商保证合格的产品”。
On 12 January 2021, the South Korean Ministry of Trade, Industry, and Energy (MOTIE) issued a draft amendment to the Electrical Appliances and Consumer Products Safety Control Act Enforcement Rules.
The draft was issued for a more rational operation of the household goods safety management system, primarily changing the safety control level of ice machines to “products subject to the supplier’s assurance of conformity” from “products subject to safety assurance”.
Interested parties may submit their comments via email to firstname.lastname@example.org or online before 13 March 2021.
In January of 2021, a series of standards were published by the Thai Ministry of Industry, covering Washing Machines, Air Conditioners, Humidifiers, portable heating tools, and similar appliances, etc. For details and implementation dates, please contact us.
灯具 / LED Luminaires / LED
2021年2月11日，巴西INMETRO / CONMETRO发布第78/2021号法规，该法规标准批准了直管，圆形和紧凑型管状荧光灯电子镇流器的技术法规。该法规将于2021年3月1日生效。
On 11 February 2021, the Brazil National Institute of Metrology, Standardization and Industrial Quality (INMETRO/CONMETRO) published Portaria No. 78/2021 which approves the Technical Regulation for Electronic Ballasts for Straight, Circular, and Compact Tubular Fluorescent Lamps.
The Regulation applies to electronic ballasts powered by the alternating current for straight, circular, and compact tubular fluorescent lamps, marketed separately or as part of luminaires and marketed as part of a kit with compact tubular fluorescent lamps when there is the possibility of using the ballasts separately.
Suppliers of electronic ballasts shall comply with the provisions of this Regulation. Products manufactured, imported, distributed, and marketed in the national territory must be safe for the user and the environment.
Accordingly, Article 5 establishes that manufacturers and importers must ensure that the products placed on the market, free of charge or not, meet all the requirements of this Regulation. Also, the other participants in the production and supply chain must maintain the integrity of the product and its markings, thus preserving compliance with the requirements of this Regulation.
All products in scope must comply with Brazilian technical standards ABNT NBR 14417:2011 AC supplied electronic ballasts for tubular fluorescent lamps – General and safety requirements and ABNT NBR 14418:2011 AC supplied electronic ballasts for tubular fluorescent lamps – Performance requirements. The certification of the products by an accredited body by Inmetro may facilitate proof of compliance with the minimum safety requirements.
Furthermore, ballasts certified in line with the provisions of Article 7(1) cannot bear the Conformity Identification Seal provided for by Portaria No. 267/2009. However, products manufactured and imported prior to 6 July 2020, certified in accordance with Portaria No. 267/2009, maybe marketed bearing the Conformity Identification Seal until the end of the stock.
2020年12月24日，俄罗斯联邦政府发布第2255号决议，批准照明用交流电路中使用的照明设备和电灯的能效要求。 根据第31条，应通过授权实验室的测试报告或通过制造商的声明证明产品合格。 该决议于2021年1月1日生效，并将会在TR EAEU 048/2019 (能耗设备能效要求技术法规) 生效之日起24个月后失效。
On 24 December 2020, the Russian Federation Government issued Resolution No. 2255 to approve energy efficiency requirements for lighting devices and electric lamps used in AC circuits for lighting purposes.
The Resolution provides requirements on the energy efficiency of general lamps, and certain types of fluorescent lamps, incandescent lamps, LED lamps, and high-pressure lamps, as well as performance requirements for the said products.
According to Article 1, the requirements do not apply to:
In accordance with Article 31, product conformity should be demonstrated by test reports from authorized laboratories or through a declaration by the manufacturer.
The Resolution entered into force on 1 January 2021 and ceases to be valid 24 months after the date of entry into force of TR EAEU 048/2019.
埃及贸易和工业部宣布，埃及标准ES 7823 / 2020 《灯具的能源效率要求》的过渡期已延长一年至2022年2月3日，或至该标准修订，以先到者为准。 生产商和进口商可以继续依照标准7823/2014灯具的能源效率要求。
The Egyptian Ministry for Trade and Industry has announced that the transitional period for Egyptian Standard ES 7823/2020 on Energy Efficiency Requirements for Lamps and Luminaries has been extended by one year until 3 February 2022, or until the Standard is amended, whichever comes first.
In the meantime, producers and importers can continue to follow the Egyptian Standard 7823/2014 Energy Efficiency Requirements for Electrical Lamps.
South Korea 韩国
2021年2月5日，韩国贸易，工业和能源部 (MOTIE) 发布《电器和消费品安全控制法实施细则》修正案草案。本草案考虑到将灯具的电源跟踪系统添加到受安全控制的产品列表中。有兴趣的单位可在2021年3月21日之前在线提交评论。
On 5 February 2021, the South Korean Ministry of Trade, Industry, and Energy (MOTIE) issued a draft amendment to the Electrical Appliances and Consumer Products Safety Control Act Enforcement Rules.
Considering that Electrical Supply Track Systems for Luminaires are added to the list of products subject to safety control, this draft adds the said products to the luminaire section of Annex 1 on the model classification of electrical appliances.
Interested parties may submit their comments online before 21 March 2021.
South Korea 韩国
2021年2月5日，韩国技术标准局 (KATS) 发布《电器和消费品安全控制法案》的修订草案。 该草案将灯具的供电轨道系统添加到受安全保证的电器中。有兴趣的单位可在2021年3月21日之前在线提交评论。
On 5 February 2021, the South Korean Agency for Technology and Standards (KATS) issued a draft amendment to the Operation Bulletin of Electrical Appliances and Consumer Products Safety Control Act
Interested parties may submit their comments via email to email@example.com or phone (82-43-870-5443) before 21 March 2021.
In January of 2021, a series of standards were published by the Thai Ministry of Industry, covering double-capped LED lamps, Self-Ballasted LED-Lamps, Fixed General Purpose Luminaires, portable general purpose luminaires, etc. For details and implementation dates, please contact us.
光伏 / 太阳能组件 Photovoltaic / Solar Modules
MNRE again extended the self-certification for SPV inverters from 2020/12/31 to 2021/06/30 and SPV inverters can be imported based on valid IEC certificates.
South Korea 韩国
对于【可充纽扣型锂电池】，如果是软包的，于2021年1月中旬开始落入KC 62133-2管控范围，需要申请KC安全证书。如果是金属外壳的纽扣电池，则不在KC管控范围，还是可以使用IEC 62133-2：2017 CB去转KC证书。
As shown below picture, regarding the form of coin type, if it is a soft type the same as below, it needs to be KC certified. However, if it is made of metal and has the same shape as a coin type, it is not subject to KC certification; it can be also proceeded with a CB certificate and test report like other projects.
泰国工业部于2021年1月21日发布并立即实施关于电动道路车辆推进用二次电池 (锂除外) 的性能标准TIS 61982-2563。
This Announcement published in the Gazette with immediate effect on 21 January 2021 by the Thai Ministry of Industry, establishes Industrial Standard TIS 61982-2563 on Secondary Batteries (Except Lithium) for the Propulsion of Electric Road Vehicles – Performance and Endurance Tests, in accordance with the Industrial Product Standards Act.
The Standard is based on IEC 61982:2012 and is applicable to performance and endurance tests for secondary batteries used for vehicle propulsion applications. Its objective is to specify certain essential characteristics of cells, batteries, monoblocks, modules, and battery systems used for propulsion of electric road vehicles, including hybrid electric vehicles, together with the relevant test methods for their specification.
The tests may be used specifically to test batteries developed for use in vehicles such as passenger vehicles, motorcycles, commercial vehicles, etc. However, the Standard does not apply to battery systems for specialist vehicles such as public transport vehicles, refuse collection vehicles, or heavy-duty vehicles, where the battery is used in a similar way to the industrial vehicles.
The test procedures are defined as a function of the vehicle requirements of the performance. The standard is applicable to lead-acid batteries, Ni/Cd batteries, Ni/MH batteries, and sodium-based batteries used in electric road vehicles.
The Standard consists of scope, definitions, general test requirements, rated capacity, dynamic discharge performance test, dynamic endurance test, and performance testing for battery systems, etc.
能源效率要求 Energy Efficiency Requirements
2021年1月29日，EEC理事会决定将EAEU TR 048/2019《能耗设备能效要求技术法规》推迟到2022年9月1日实施。
On January 29, the EEC Council decided to postpone enactment of the Union’s Technical regulation “On requirements for energy efficiency of power-consuming devices “(EAEU TR 048/2019)” to September 1, 2022. This initiative was put forward by the Russian party.
The effective date was postponed to grant manufacturers extra time to ensure a smooth transition to the requirements of the unified technical regulation. Besides the decision appreciates the necessity for measures aimed at normalizing the business environment and restoring business activities in light of the gradual removal of restrictions associated with the spread of new coronavirus infection.
Furthermore, the same document has established a deferred standard for energy efficiency marking of vacuum cleaners as well as postponed the date of entry into force of decision adopted by the EEC Council establishing the forms of labels for various types of power-consuming devices and their drafting rules to March 1, 2022; individual requirements set out in Annexes Nos. 3, 5, 6, 9, 12, 13 and 14 to the technical regulation, for a year.
The Ukrainian Ministry of Energy adopted Order No. 676 approving the energy labeling requirements for local space heaters.
The Technical Regulations are modeled on the criteria contained in EU Regulation No. 1186/2015. This Order establishes the requirements for the energy labeling of local heaters with a nominal heat output ≤ of 50 kW.
This Order enters into force on 28 December 2021.
On 26 October 2020, the Ukrainian Ministry of Energy adopted Order No. 683 approving Technical Regulations (TR) establishing energy labeling requirements for professional refrigerated storage cabinets.
The Technical Regulations are modeled on Commission Delegated Regulation (EU) 2015/1094 of 5 May 2015 supplementing Directive 2010/30/EU with regard to the energy labeling of professional refrigerated storage cabinets.
They establish requirements for the labeling and the provision of supplementary product information of professional refrigerated storage cabinets. They shall apply to electric mains-operated professional refrigerated storage cabinets, including those sold for the refrigeration of foodstuffs and animal feed.
The Technical Regulations provide a six-month transitional period for the marketing of all non-compliant devices put into circulation before the entry into force of this Order.
This Order enters into force on 4 July 2021.
其他 / 多主题产品 Others / Products with Multiple Subjects
2021年2月9日，中国国家认证认可监督管理委员会 (CNCA) 发布修订相关标准时强制性产品认证自我声明评估方法实施要求的公告。 使用CCC自我声明评估方法的产品制造商应积极跟踪并收集有关标准的修订版，在新版标准实施一年内完成新版标准自我声明换版。在新版标准实施后，应依据新版标准实施评价。新版标准实施前已经出厂、投放市场且不再生产的产品，无需进行新版标准自我声明换版。
On 9 February 2021, the Certification and Accreditation Administration of China (CNCA) published an announcement on implementation requirements of compulsory product certification self-declaration evaluation methods when relevant standards are revised.
The manufacturer of the product that applies the CCC self-declaration evaluation method should actively track and collect the revision of the relevant standards.
The manufacturers should implement self-declaration in the following way when the standard is revised:
沙特 Saudi Arabia
SASO has stopped the flexibility which was given due to the COVID-19 pandemic to accept the EER test reports with 5 years validity.
In this regard, the test report shall not exceed the below validity:
4001183833 / 8009993668